Air filter, flat paper cartridge type for models with single throttle body

See SIA10434 for a reusable performance air filter

AP8104924

Dimensions:
120mm x 80mm x 53mm

UFI 25 531 00 cartridge oil filter for 1989 on small block engines. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick, If this item is out of stock we do stock a like for like replacement, which is this item SIA27301 .

For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer). Some 750 XPA models use SIA19530, we advise you to check your old filter before ordering. Also known as Guzzi ref. 2A000633

 27153085 GU27153085 27 15 30 85
 2715 3085 2715.3085 27.15.30.85

Dimensions:
120mm x 45mm diameter overall

Rotational oil seal for crownwheel carrier in drive box on post 1974 big twins. Front crank oil seal on loop frame models

Also known as Guzzi ref. 90403850 and used on 850 GT and loop frame models for front crank oil seal ( 90403851 )

 90413850 GU90413850 90 41 38 50
 9041 3850 9041.3850 90.41.38.50

Dimensions:
38mm x 50 mm x 7mm

Guzzi Base Workshop Manual for all V35 & 50 models. 134 pages covering the basics for all V35 & V50 models

Much of the information in this manual is also relevant to V65, V75 and 750 small twins. Use this manual in combination with the relevant supplement if your small twin isn't a V35 / V50 mark 1 or 2.
This manual includes common torque settings for small twins.

 23920181 GU23920181 23 92 01 81
 2392 0181 2392.0181 23.92.01.81

Dimensions:
A4 - 134 pages black & white

Pair of EBC FA018 brake pads for P2 F08 (P8) calipers.

For P08/F08 calipers. Front and rear pads for all models except P9 equipped Spada where these are only for front calipers

28654601-z 28654601 GU28654601 28 65 46 01
 2865 4601 2865.4601 28.65.46.01

Also fits Benelli 354 Rear, Benelli Sei Fronts, Ducati 250/350/450 Desmo Fronts (-1976), Ducati Pantah, Ducati F1, Ducati 750 Paso Fronts (1987-1990), Ducati 750 Sport (1988-1990), Ducati 860 GT/GTS, Ducati 900 GTS, Ducati Hailwood Rep, Ducati 900 Darmah (1977-1978), Ducati 906 Paso (1988-1989), Ducati 1000 R1 Hailwood Ref., Hesketh, Horex HRD 600, Horex 500/600 Columbus, Laverda 750 SF2 Fronts, Laverda 750 SFC, Laverda 750 SF3, Laverda 1000 3C (1974-1978), Laverda 1000 3CL (1976-1981), Laverda 1000 RGS/RGA, Laverda 1000 RGS Corsa Rear, Laverda 1000 SFC, Laverda 1200 (1978-1979), Laverda 1200 TS/Mirage (1981), MZ ETZ 125/150/250/300 Fronts (1985-1992), Norton Classic (1989), Norton Interpol (1989), Triumph T140 (1985-1988 Brembo)

Dimensions:
55.7 x 55 x9mm

Final drive inner seal

For Breva 750 up to frame no. LL111907

90407590-z 90407590 GU90407590 90 40 75 90
 9040 7590 9040.7590 90.40.75.90

Dimensions:
90mm OD

Front wheel bearing, sealed

2 bearings required per wheel, Also used as rear wheel bearing on V7 850

 92204221 GU92204221 92 20 42 21
 9220 4221 9220.4221 92.20.42.21

Dimensions:
42mm OD

Bearing used as UJ carrier bearing on pre 2007 models (see TRA90062 for retaining circlip). Used as outer crownwheel carrier bearing on CARC units

 92204230 GU92204230 92 20 42 30
 9220 4230 9220.4230 92.20.42.30

Dimensions:
62mm OD

Taper needle roller bearing used as steering head bearing

2 sets required per bike. Also used as rear drive box pinion bearing on big twins with rear drum brake

 92249225 GU92249225 92 24 92 25
 9224 9225 9224.9225 92.24.92.25

Gearbox input seal and output shaft oil seal on big twins, fork seal on Nuovo Falcone. Used as crownwheel shaft oil seal on small twins. Output seal only on 4 speed gearboxes

Supercedes Guzzi ref. 90403547. Used as crownwheel carrier seal on small twins Also known as Guzzi ref. 90403549

 90403548 GU90403548 90 40 35 48
 9040 3548 9040.3548 90.40.35.48

Dimensions:
47mm OD