Dust cover for fork seals

Suitable for V11 models with 40mm Marzocchi forks, also known as Piaggio ref. 599502, 00H00202231, AP8123201, AP8123296, AP8123777
See SUA01535 for 43mm version.

 01530571 GU01530571 01 53 05 71
 0153 0571 0153.0571 01.53.05.71

Also fits Aprilia RS 125 (2006-2010), Aprilia, RX-SX 125 (2008-2010), Gilera Nexus 500 E3 (2006-2008), Piaggio X9 500 Evolution (2006-2007)

Exhaust gasket, silencer bush or muffler gasket shim for exhaust joint between silencer and downpipe

2 exhaust bushes required per bike

 91113826 GU91113826 91 11 38 26
 9111 3826 9111.3826 91.11.38.26

Dimensions:
38mm ID x 44mm OD x 26mm

Chrome finish mirror, especially suited to T3, V50 and similar models. Conventional M10 thread, head is socket mounted for left or right hand fitment. Head is chromed plastic, stem is chromed steel.

M10 thread

Dimensions:
M10 conventional thread, 105mm diameter head, 180mm approx reach

Black handlebar mounted mirror. Conventional M10 thread, head is threaded for left or right hand fitment.

Supercedes BUMM mirror HAA36021W. See ACA00101 for a black mirror extender kit to extend the reach of this mirror.

Dimensions:
M10 conventional thread, approx. 240mm reach to far edge of mirror, mirror 110mm diameter

Ducati type regulator rectifier for models fitted with the later 350W Ducati charging system. Supplied wired with 1 x 4 pin and 1 x 2 pin block connector

Also known as Guzzi ref. 03703870. Note that some models have a different white connector block, if you have this connector then you will need to modify the connector to fit. This includes the mk 1 V7 Special and V7 Stone

 32703810 GU32703810 32 70 38 10
 3270 3810 3270.3810 32.70.38.10

EFC cartridge oil filter for 1989 on small block engines. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick

For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer). Some 750 XPA models use SIA19530, we advise you to check your old filter before ordering. Also known as Guzzi ref. 2A000633

 27153085 GU27153085 27 15 30 85
 2715 3085 2715.3085 27.15.30.85

Dimensions:
120mm x 45mm diameter overall

Throttle cable, two cables required

We advise you to measure your existing cable before ordering in case you have a non standard set up.

 28117511 GU28117511 28 11 75 11
 2811 7511 2811.7511 28.11.75.11

Dimensions:
Inner length 1176mm, 1010mm outer

Throttle cable for high bar models, runs from twistgrip to carb

We advise you to measure your existing cable before ordering in case you have a non standard set up.

 19117595 GU19117595 19 11 75 95
 1911 7595 1911.7595 19.11.75.95

Dimensions:
1101mm outer length, 105mm free length, 5.7mm barrel nipple, 2.7mm barrel nipple

Steel fixed rear brake pipe with threaded connectors at each end

Rigid brake pipe

 17658650 GU17658650 17 65 86 50
 1765 8650 1765.8650 17.65.86.50

Dimensions:
Length 239mm, 15mm tip to under hex head

Head gasket

19022062-z 19022062 GU19022062 19 02 20 62
 1902 2062 1902.2062 19.02.20.62

Dimensions:
82mm ID for 80mm barrel