Oil pressure switch. May be supplied with a vertical spade connector, this supercedes the original Guzzi part which is no longer available. This version will fit without removal of the alternator
See ENA12640 for replacement crush washer and ELA10005 for female spade connector
2 in stock
31768780 GU31768780 31 76 87 80
3176 8780 3176.8780 31.76.87.80
£11.00
INC VAT
£9.17 EX VAT
Pair of original style Ariete closed end black handlebar grips - lattice pattern.
More than 5 in stock
14603000-z 14603000 GU14603000 14 60 30 00
1460 3000 1460.3000 14.60.30.00
£18.50
INC VAT
£15.42 EX VAT
Stainless steel drain plug for drive box and gearbox, includes recess for crush washer to locate in. Also used as level plug on big twins and front sump drain on small twins.
Also known as Guzzi ref. 95980212, 95980610. Use crush washer SIA10900 with this bolt
More than 5 in stock
95980214-z 95980214 GU95980214 95 98 02 14
9598 0214 9598.0214 95.98.02.14
£9.90
INC VAT
£8.25 EX VAT
Stainless steel tool for removing Bosch alternator rotor. Will also fit Saprisa.
Simply screw in until the rotor pops off
3 in stock
Also fits Benelli Sei 900 (Series 2)
£6.60
INC VAT
£5.50 EX VAT
M12 pivot bolt kit for brake and gear lever pivots on Tonti framed models. Kit consists of 1 M12 bolt (with hex head and slotted other end), wavy washer, flat washer and half nut
Beautifully made to enhance the appearance of your bike, also cheaper than OE non stainless parts. Guzzi parts refs: 30252360, 98073660, 95100409, 92701120, 17252350. Does not fit G5
5 in stock
98053660-z 98053660 GU98053660 98 05 36 60
9805 3660 9805.3660 98.05.36.60
£17.50
INC VAT
£14.58 EX VAT
Fine thread screw in brakelight switch for linked system proportioning valve or splitter. See ELA12735 for rubber cap
Stop light switch also known as Guzzi ref. 63657000
3 in stock
79654116 GU79654116 79 65 41 16
7965 4116 7965.4116 79.65.41.16
Also fits Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 GT/Sport Köwe, Ducati 750 Paso (1984-1992), Ducati 750 Sport, Ducati 750/900 SS Köwe, Ducati 750 F1/Laguna Seca, Ducati 860/900 GTS, Ducati 900 Darmah, Ducati 900 MHR-I, Ducati 900 SS (1990), Ducati 906 Paso (1988), Ducati 1000 MHR-2/S2
£21.40
INC VAT
£17.83 EX VAT
Dust cover for fork leg, seals against stanchion to protect fork seal
More than 5 in stock
14524500-z 14524500 GU14524500 14 52 45 00
1452 4500 1452.4500 14.52.45.00
£11.50
INC VAT
£9.58 EX VAT
Black rubber UJ gaiter / boot, clips available separately - see SSA64990 and TRA12544
More than 5 in stock
18548000 GU18548000 18 54 80 00
1854 8000 1854.8000 18.54.80.00
£12.50
INC VAT
£10.42 EX VAT
Thottle cable, runs from twistgrip to carb
We advise you to measure your existing cable before ordering in case you have a non standard set up.
4 in stock
19117580 GU19117580 19 11 75 80
1911 7580 1911.7580 19.11.75.80
£10.00
INC VAT
£8.33 EX VAT
New type clutch friction plate for models with deep splines with deep splined centre
2 plates required- thicker side of each friction plate should face transmission.
Also known as Guzzi ref. 30084410, 03084400, 29084450
V11 Tenni, Rosso Mandello and Scura have a single plate clutch which uses a different friction plate (unfortunately out of production)
These can be fitted to earlier 850 and 1000 models if the early shallow splined clutch centre is replaced with the later deep splined type. See our kit CLA20302 to update early 850/1000 models. Clutch plate alignment tool also available, see TOA30510
4 in stock
05084430 GU05084430 05 08 44 30
0508 4430 0508.4430 05.08.44.30
£57.70
INC VAT
£48.08 EX VAT