Polished aluminium clutch lever
Also known as Guzzi ref. 2B001300
1 in stock
2B002390
£38.00
INC VAT
£31.67 EX VAT
1 metre of Ariete fuel pipe suitable for fuel and breather pipe applications on gravity fed non injection models, cut your fuel lines to your own spec
Certified ethanol proof and safe for modern E10 fuel. Hose clips also available, see FUA00004
More than 5 in stock
£8.50
INC VAT
£7.08 EX VAT
Bearing used as UJ carrier bearing on pre 2007 models (see TRA90062 for retaining circlip). Used as outer crownwheel carrier bearing on CARC units
3 in stock
92204230 GU92204230 92 20 42 30
9220 4230 9220.4230 92.20.42.30
£14.40
INC VAT
£12.00 EX VAT
Gearbox input seal and output shaft oil seal on big twins, fork seal on Nuovo Falcone. Used as crownwheel shaft oil seal on small twins. Output seal only on 4 speed gearboxes
Supercedes Guzzi ref. 90403547. Used as crownwheel carrier seal on small twins Also known as Guzzi ref. 90403549
More than 5 in stock
90403548 GU90403548 90 40 35 48
9040 3548 9040.3548 90.40.35.48
£18.50
INC VAT
£15.42 EX VAT
Rear crankcase oil seal or rear main oil seal.
Fits Nevada 750 up to engine LT017877 and Nevada 350 to engine PC053625. Also known as Guzzi ref. 90405368. We recommend replacing the rear crank oil seal when replacing the clutch
More than 5 in stock
90405367-z 90405367 GU90405367 90 40 53 67
9040 5367 9040.5367 90.40.53.67
£14.00
INC VAT
£11.67 EX VAT
One litre AGIP brake and clutch fluid, this is a high performance DOT 3 and 4 fluid suitable for all Moto Guzzis
Mixes safely with other DOT 3 , DOT 4 and DOT 5.1 brake and clutch fluids. If you are having problems bleeding your brakes you may need one of our one way bleed nipples BRA41651 and BRA41650
Please note this part CANNOT be posted outside of the UK mainland area.
See BRA99014 for high performance alternative
More than 5 in stock
£13.75
INC VAT
£11.46 EX VAT
A4 marine grade stainless steel M6 bleed nipple for Brembo F05 and twin bleed P2 F08 & F09 calipers. Manufactured specially for Gutsibits as a replica of the original Brembo M6 bleed nipple
Use M10 bleed screw SSA36794 for single bleed (later) P8 calipers. Ducati ref. 079539787
See BRA36794 for rubber cap
More than 5 in stock
Also fits Benelli 250 TS, Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 F1/Laguna Sec, KTM 250XC, KTM 250SX, KTM 250EXC,
£8.00
INC VAT
£6.67 EX VAT
Zadi ignition switch with 2 keys
4 male spade type connectors on underside, replaces original switch with bullet connectors. See ELA10005 for female spade connectors and FRA19741 for rubber wiring boot
More than 5 in stock
31735360 GU31735360 31 73 53 60
3173 5360 3173.5360 31.73.53.60
Also fits Benelli 750 Sei (series 2) - fits with minor modification
£31.00
INC VAT
£25.83 EX VAT
Needle roller bearing used in lower suspension linkage for rear shock absorber. 7 bearings required per bike
See SUA81068 for bearing oil seal
More than 5 in stock
AP8110066
£6.60
INC VAT
£5.50 EX VAT
Dimensions:
10mm threaded shank, 11mm across flats, 8mm OD at base, 15mm from tip to underside of flats
Stainless steel M10 bleed nipple for Brembo single bleed P2 F08 (P8) calipers on pre 1998 models. This is the same length as the genuine Brembo part BRA17659. M10 bleed screw used only on rear of 2003 on models
Part of Guzzi ref. 17659260. Some brake calipers may require a longer bleed screw, we reecommend measuring your existing screw - it should be 15mm from under the flats to the base of the tip.
More than 5 in stock
£8.20
INC VAT
£6.83 EX VAT