Gearbox input seal and output shaft oil seal on big twins, fork seal on Nuovo Falcone. Used as crownwheel shaft oil seal on small twins. Output seal only on 4 speed gearboxes

Supercedes Guzzi ref. 90403547. Used as crownwheel carrier seal on small twins Also known as Guzzi ref. 90403549

 More than 5 in stock

 90403548 GU90403548 90 40 35 48
 9040 3548 9040.3548 90.40.35.48

Rear crankcase oil seal or rear main oil seal.

Fits Nevada 750 up to engine LT017877 and Nevada 350 to engine PC053625. Also known as Guzzi ref. 90405368. We recommend replacing the rear crank oil seal when replacing the clutch

 More than 5 in stock

90405367-z 90405367 GU90405367 90 40 53 67
 9040 5367 9040.5367 90.40.53.67

One litre AGIP brake and clutch fluid, this is a high performance DOT 3 and 4 fluid suitable for all Moto Guzzis

Mixes safely with other DOT 3 , DOT 4 and DOT 5.1 brake and clutch fluids. If you are having problems bleeding your brakes you may need one of our one way bleed nipples BRA41651 and BRA41650

Please note this part CANNOT be posted outside of the UK mainland area.

See BRA99014 for high performance alternative

 More than 5 in stock

A4 marine grade stainless steel M6 bleed nipple for Brembo F05 and twin bleed P2 F08 & F09 calipers. Manufactured specially for Gutsibits as a replica of the original Brembo M6 bleed nipple

Use M10 bleed screw SSA36794 for single bleed (later) P8 calipers. Ducati ref. 079539787

See BRA36794 for rubber cap

 More than 5 in stock

Also fits Benelli 250 TS, Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 F1/Laguna Sec, KTM 250XC, KTM 250SX, KTM 250EXC,

Steel intermediate clutch plate

 2 in stock

12082300-z 12082300 GU12082300 12 08 23 00
 1208 2300 1208.2300 12.08.23.00

Zadi ignition switch with 2 keys

4 male spade type connectors on underside, replaces original switch with bullet connectors. See ELA10005 for female spade connectors and FRA19741 for rubber wiring boot

 More than 5 in stock

 31735360 GU31735360 31 73 53 60
 3173 5360 3173.5360 31.73.53.60

Also fits Benelli 750 Sei (series 2) - fits with minor modification

Dellorto choke piston or plunger for Dellorto VHB, PHBH, PHF and PHM carbs. Includes rubber seal in end of plunger

 More than 5 in stock

 13937800 GU13937800 13 93 78 00
 1393 7800 1393.7800 13.93.78.00

Universal hydraulic brake light switch. This hydraulic switch replaces discontinued brakelight switches by bolting in place of a single banjo bolt on the handlebar or rear brake master cylinder

NB stop light switch may be supplied with or without 2 pin block connector. Can be used in place of Guzzi ref. 32657060

 2 in stock

Brakelight switch

Stop light switch also known as Guzzi ref. AP8224192
See FRA98412 for mounting screw

 3 in stock

03749845-z 03749845 GU03749845 03 74 98 45
 0374 9845 0374.9845 03.74.98.45

Stainless steel M10 bleed nipple for Brembo single bleed P2 F08 (P8) calipers on pre 1998 models. This is the same length as the genuine Brembo part BRA17659. M10 bleed screw used only on rear of 2003 on models

Part of Guzzi ref. 17659260. Some brake calipers may require a longer bleed screw, we reecommend measuring your existing screw - it should be 15mm from under the flats to the base of the tip.

 More than 5 in stock