Drive box input seal
Pinion oil seal
More than 5 in stock
90403251-z 90403251 GU90403251 90 40 32 51
9040 3251 9040.3251 90.40.32.51
£16.60
INC VAT
£13.83 EX VAT
Carb gasket kit / rebuild kit for 1 Dellorto PHF carb. Suitable for all PHF carbs with accelerator pumps including PHF36. Dellorto ref. 52514-77
Carb overhaul kit, float bowl seal FUA90001 and fuel filter FUA60888 also available separately to this carb seal kit
More than 5 in stock
14939950 GU14939950 14 93 99 50
1493 9950 1493.9950 14.93.99.50
Also fits Hesketh, Laverda
£18.75
INC VAT
£15.62 EX VAT
Speedo sensor with 100cm lead and 3 pin plug for non ABS equipped models
1 in stock
AP8124985
£252.00
INC VAT
£210.00 EX VAT
Silencer clamp gasket / shim or muffler gasket used to seal crossover to silencer
This exhaust bush is not required if a Mistral or Agostini silencer is fitted
1 in stock
05128230 GU05128230 05 12 82 30
0512 8230 0512.8230 05.12.82.30
£25.00
INC VAT
£20.83 EX VAT
Front brake master cylinder cap and rubber kit for Brembo PS 13 master cylinder. Check the screw holes in your master cylinder are diagnally opposed (as seen top left and bottom right corners when sitting on bike)
Reservoir cap replaces Guzzi ref. 2B001928
1 in stock
03661145 GU03661145 03 66 11 45
0366 1145 0366.1145 03.66.11.45
£54.00
INC VAT
£45.00 EX VAT
Complete LED indicator with lead. Fits front right or rear left
1 in stock
2D000439
£45.00
INC VAT
£37.50 EX VAT
Pair of Brembo 07BB1408 carbon ceramic brake pads for Brembo P2 F08 (P8) calipers
For P08/F08 calipers. Front and rear pads for all models except P9 equipped Spada where these are only for front calipers
4 in stock
28654601-z 28654601 GU28654601 28 65 46 01
2865 4601 2865.4601 28.65.46.01
Also fits Benelli 354 Rear, Benelli Sei Fronts, Ducati 250/350/450 Desmo Fronts (-1976), Ducati Pantah, Ducati F1, Ducati 750 Paso Fronts (1987-1990), Ducati 750 Sport (1988-1990), Ducati 860 GT/GTS, Ducati 900 GTS, Ducati Hailwood Rep, Ducati 900 Darmah (1977-1978), Ducati 906 Paso (1988-1989), Ducati 1000 R1 Hailwood Ref., Hesketh, Horex HRD 600, Horex 500/600 Columbus, Laverda 750 SF2 Fronts, Laverda 750 SFC, Laverda 750 SF3, Laverda 1000 3C (1974-1978), Laverda 1000 3CL (1976-1981), Laverda 1000 RGS/RGA, Laverda 1000 RGS Corsa Rear, Laverda 1000 SFC, Laverda 1200 (1978-1979), Laverda 1200 TS/Mirage (1981), MZ ETZ 125/150/250/300 Fronts (1985-1992), Norton Classic (1989), Norton Interpol (1989), Triumph T140 (1985-1988 Brembo)
£31.50
INC VAT
£26.25 EX VAT
49cm length of black pipe with clips for connecting rear master cylinder to brake fluid reservoir
Brake fluid, oil and fuel resistant. We recommend measuring your existing pipe first to check ensure this 49cm pipe will be long enough. This is not long enough for the rear brake master cylinder on V50 II and V35 I
More than 5 in stock
£8.80
INC VAT
£7.33 EX VAT
Single stainless steel M10 banjo bolt with bleed nipple for Brembo fittings. Supplied with bleed nipple cap and crush washers. Perfect for bleeding up old P9, F08 and F05 calipers where the bleed nipple has broken off. This can also be used to add additional bleed points to linked systems where airlocks are causing problems
These can be used to replace the standard banjo bolt on CARC models. See alternative part BRA41653 for Stahlbus auto bleed banjo bolt
More than 5 in stock
Also fits Benelli 250 TS
£21.00
INC VAT
£17.50 EX VAT
UFI 25 46 500 cartridge oil filter. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick
For post 1989 V35, V50 and V65 models use SIA27300 .
NB Packaging may vary. For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer)
More than 5 in stock
19153000 GU19153000 19 15 30 00
1915 3000 1915.3000 19.15.30.00
£8.50
INC VAT
£7.08 EX VAT