Full engine and gearbox seal kit, includes all necessary seals for a complete engine and gearbox overhaul.

Full gasket sets also available. Can also be fitted to models equipped with a Saprisa charging system if front crank oil seal ENA94238 is ordered

 More than 5 in stock

 17999550 GU17999550 17 99 95 50
 1799 9550 1799.9550 17.99.95.50

Set of 12 cush drive rubbers

Contains 12 rubbers, also known as Guzzi ref. 14336803

 1 in stock

 01336800 GU01336800 01 33 68 00
 0133 6800 0133.6800 01.33.68.00

Carb gasket kit / rebuild kit for Dellorto PHBH carbs

Carb overhaul kit, float bowl seal FUA90001, fuel filter FUA60888 and float bowl washer FUA27720 available separately to this carb seal kit

 More than 5 in stock

 19939980 GU19939980 19 93 99 80
 1993 9980 1993.9980 19.93.99.80

Dellorto choke piston or plunger for Dellorto VHB, PHBH, PHF and PHM carbs. Includes rubber seal in end of plunger

 More than 5 in stock

 13937800 GU13937800 13 93 78 00
 1393 7800 1393.7800 13.93.78.00

Brembo brake caliper rebuild kit for one P2 F08 (P8) caliper, contains 2 pairs of seals, O ring and 2 M10 bolts

This seal kit is for F08 calipers fitted to front of all these models. Also used on some Triumph Bonnevilles, MZs, Ducati 600 Pantah, 500 Pantah, 500 Sport Desmo, 500 GTV, 650 SL, 750 F1, 750 F1B, 750 Paso, 750 Sport, 900 MHR, 900 SS, 900 S2, 906 Paso, 100 R1, 100 S2 Desmo, Laverda Jota 1000 and Laverda 1200 Anniversary. Brembo ref. 120274110

See BRA10310 for less expensive replica kit

 More than 5 in stock

 14659000 GU14659000 14 65 90 00
 1465 9000 1465.9000 14.65.90.00

Also fits Benelli 354, Benelli Sei, Ducati 250/350/450 Desmo (-1976), Ducati Pantah, Ducati F1, Ducati 750 Paso (1987-1990), Ducati 750 Sport (1988-1990), Ducati 860 GT/GTS, Ducati 900 GTS, Ducati Hailwood Rep, Ducati 900 Darmah (1977-1978), Ducati 906 Paso (1988-1989), Ducati 1000 R1 Hailwood Ref., Hesketh, Horex HRD 600, Horex 500/600 Columbus, Laverda 750 SF2, Laverda 750 SFC, Laverda 750 SF3, Laverda 1000 3C (1974-1978), Laverda 1000 3CL (1976-1981), Laverda 1000 RGS/RGA, Laverda 1000 SFC, Laverda 1200 (1978-1979), Laverda 1200 TS/Mirage (1981), MZ ETZ 125/150/250/300 (1985-1992), Norton Classic (1989), Norton Interpol (1989), Triumph T140 (1985-1988 Brembo)

Carb mounted flip choke with plunger, lever, O ring, casting and spring. Insufficient clearance on high top carbs to operate the choke and the throttle cable

Fits all PHF30 - PHF36 and VHB30 Dellorto flat top carbs, contains rubber seat insert. Allows you to eliminate the choke cables and any handlebar choke controls for a cleaner look, especially suitable for special builds

 2 in stock

 14937800 GU14937800 14 93 78 00
 1493 7800 1493.7800 14.93.78.00

Brembo brake master cylinder overhaul kit for overhauling foot operated PS 15 master cylinders on linked systems. Includes all seals and brake grease

This seal kit replaces Guzzi part numbers 17659350, 66139790. Brembo ref. 110273920. This repair kit also used on some Cagiva 650 Elefant models and Benelli Sei. Some Nevada 750 models use BRA14701, check your rear master cylinder before ordering. See this link for help with fitting this kit. Supercedes front kit BRA11043
Note that this kit is only for PS15 models where the piston is retained by a ring, if your master cylinder has a circlip retaining the piston then you have a PS 16 and you will need to replace the whole master cylinder - see BRA19001 for a replacement

 More than 5 in stock

 10273920 GU10273920 10 27 39 20
 1027 3920 1027.3920 10.27.39.20

Also fits Benelli Sei, Cagiva Elefant, Ducati 600 SL Pantah, Ducati 750/900 SS, Ducati 860/900 GTS, Ducati 900 Darmah, Ducati 900 MHR, Ducati 1000 MHR, Ducati 750 Sport (1972-1974), Laverda Jota

Oil pressure sender, M12 thread, male bullet connector

Supercedes Guzzi no. 12768700. Some small twins also require adapter 19055800 (or ELA19720 can be fitted in place of this switch). Check which type your small twin uses before replacing.

See ENA12640 for replacement crush washer if required

 More than 5 in stock

 17768750 GU17768750 17 76 87 50
 1776 8750 1776.8750 17.76.87.50

Rear crankcase oil seal or rear main oil seal.

Fits Nevada 750 up to engine LT017877 and Nevada 350 to engine PC053625. Also known as Guzzi ref. 90405368. We recommend replacing the rear crank oil seal when replacing the clutch

 More than 5 in stock

90405367-z 90405367 GU90405367 90 40 53 67
 9040 5367 9040.5367 90.40.53.67

Clutch cable for pre 1988 models with left hand switchgear integrated into clutch lever clamp

 1 in stock

28093060-z 28093060 GU28093060 28 09 30 60
 2809 3060 2809.3060 28.09.30.60