Cartridge oil filter UFI 23 149 00
Fits Daytona 1000 models where filter screws into base of sump. This is an 8 sided UFI filter.
Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump.
You may also require SIA10070 which is the crush washer for the drain plug and ENA14036 (sump gasket).
Please note that Daytona RS and T5 Polizia use filter SIA15300
More than 5 in stock
14153000 GU14153000 14 15 30 00
1415 3000 1415.3000 14.15.30.00
£10.50
INC VAT
£8.75 EX VAT
Output oil seal for drive box
This oil seal fits output side of bevel box
More than 5 in stock
90407085-z 90407085 GU90407085 90 40 70 85
9040 7085 9040.7085 90.40.70.85
£14.00
INC VAT
£11.67 EX VAT
Engine breather pipe from crankcase to spine frame
2 in stock
30157400 GU30157400 30 15 74 00
3015 7400 3015.7400 30.15.74.00
£11.50
INC VAT
£9.58 EX VAT
Set of ignition points (made up of two boxes of contacts)
More than 5 in stock
19709620 GU19709620 19 70 96 20
1970 9620 1970.9620 19.70.96.20
£32.60
INC VAT
£27.17 EX VAT
Brembo kit containing replacement seal and angled elbow for connecting remote brake fluid reservoir to PS 15, PS 11 and PS 13 rear master cylinders
Also known as Brembo ref. 110312720
2 in stock
19659500 GU19659500 19 65 95 00
1965 9500 1965.9500 19.65.95.00
£7.50
INC VAT
£6.25 EX VAT
Final drive inner output seal
For Breva 750 from frame no. LL111908
More than 5 in stock
90407591-z 90407591 GU90407591 90 40 75 91
9040 7591 9040.7591 90.40.75.91
£15.80
INC VAT
£13.17 EX VAT
Metal bush for foot brake or gear lever pivot
2 in stock
30678160 GU30678160 30 67 81 60
3067 8160 3067.8160 30.67.81.60
£15.00
INC VAT
£12.50 EX VAT
Rear crank oil seal
Fits Nevada 750 from engine LT017877 and Nevada 350 from PC053625. NB Original specification 12mm seal no longer in production, our seal is 10mm thick. Superceded by Guzzi ref. 886365
4 in stock
04000500-z 04000500 GU04000500 04 00 05 00
0400 0500 0400.0500 04.00.05.00
£13.20
INC VAT
£11.00 EX VAT
One metre of copper core HT lead, this is superior to the more commonly available carbon core lead
Sold by the metre, one metre is enough for two leads on most models with coils under the fuel tank. For models with coils under the side panel you will need two metres. See ELA14715 and ELA14714 for plug caps and ELA20001 for coil screw cap. See ELA00001 for crimp on HT lead connector
More than 5 in stock
£7.00
INC VAT
£5.83 EX VAT
Brembo caliper cover for models with obsolete twin bleed calipers
P9 caliper cover includes cutout each side for bleed nipple. Also known as Guzzi ref. 14654700, 17654760. Please note you may need to trim away the four moulded lugs at the bottom of the cover otherwise these may clash with your pad pins
4 in stock
20325410 GU20325410 20 32 54 10
2032 5410 2032.5410 20.32.54.10
£11.00
INC VAT
£9.17 EX VAT