Shop headings: New Spares | Used Spares | Accessories | Brands
Clutch cable with starter interlock switch
We advise you to measure your existing cable before ordering in case you have a non standard set up.
This part is available by special order, request a quote
17093050-z 17093050 GU17093050 17 09 30 50
1709 3050 1709.3050 17.09.30.50
£75.00
INC VAT
£62.50 EX VAT
Dimensions:
590mm wide at widest point, 465mm tall from above headlamp to top of screen. 177mm vertical centres between screen mounts
Tinted screen, black edging. Uses standard mounting points
If you're looking for a smaller Cali 1100 or Cali 3 screen please check that this screen is actually smaller than your existing one. Transparent also available by special order.
To simplify installation always mount a screen on to the mounting brackets before mounting the brackets on the bike
Fitting kits no longer available
This part is available by special order, request a quote
31577261-z 31577261 GU31577261 31 57 72 61
3157 7261 3157.7261 31.57.72.61
£75.00
INC VAT
£62.50 EX VAT
Cut out switch, threaded body. Used as sidestand switch on big twins and clutch cut out switch on V7 series small twins and Breva 750
This part is available by special order, request a quote
29759150 GU29759150 29 75 91 50
2975 9150 2975.9150 29.75.91.50
£75.00
INC VAT
£62.50 EX VAT
Pair of aluminium spacers and gaskets which allow the fitting of a round barrel rocker cover (loop or T3 type) on a square barrel engine
Rocker cover adapter kit - a simple way to get the classic round barrel appearance without swapping barrels and heads. This kit contains a pair of adapter plates and all neccessary gaskets
3 in stock
£70.00
INC VAT
£58.33 EX VAT
Long screw in polished alloy thermometer dipstick with O ring for models with a sump extension. Shows oil temperature in degrees celcius
Supplied unmarked, you will need to mark the rod using a small file to match your existing dipstick
This part is due back in stock soon, call 01484 841395 to reserve yours
28004950-z 28004950 GU28004950 28 00 49 50
2800 4950 2800.4950 28.00.49.50
£70.00
INC VAT
£58.33 EX VAT
Replacement Dellorto throttle slide for PHF36 carbs, the original slide is no longer available from Dellorto. To fit this slide you may need to make a minor modification to the slide or your carb body. This can be made with a small file or Dremel type tool, see these instructions for details
This part is available by special order, request a quote
75527554 GU75527554 75 52 75 54
7552 7554 7552.7554 75.52.75.54
£70.00
INC VAT
£58.33 EX VAT
Factory tool for clutch centre gear nut, this is a superior design tool intended for repeated use
Designed to fit the original factory spec nut- this may not fit some aftermarket items. See TOA14651 for cheaper aftermarket tool
This part is available by special order, request a quote
14912603 GU14912603 14 91 26 03
1491 2603 1491.2603 14.91.26.03
£70.00
INC VAT
£58.33 EX VAT
Gearbox bearing for output shaft input end
Two part bearing
This part is due back in stock soon, call 01484 841395 to reserve yours
92234717
£68.50
INC VAT
£57.08 EX VAT
Replacement 7" H4 sealed beam unit / reflector and glass with sidelight bulb and bulb rubber. UK spec
See ELA17740 for retaining clips. Can also be used on V7 Special etc... if pilot light is modified to avoid fuse board. Combine with brighter headlight bulb LIA11501
This part is due back in stock soon, call 01484 841395 to reserve yours
17740464 GU17740464 17 74 04 64
1774 0464 1774.0464 17.74.04.64
Also fits Ducati 350-500 Twin, Ducati Sport Desmo, Ducati 750 GT, Ducati 750SS, Ducati 900SS, Ducati 860 GTS, Ducati 900 GTS
£68.40
INC VAT
£57.00 EX VAT
Brush holder for Bosch alternator stator
Also known as Guzzi ref. 17712454, 14712452
Includes brushes. See ELA17453
1 in stock
17712452 GU17712452 17 71 24 52
1771 2452 1771.2452 17.71.24.52
£68.30
INC VAT
£56.92 EX VAT