Brembo brake master cylinder overhaul kit for handlebar, undertank (cable operated) mounted, handlebar mounted and rear PS 12 master cylinders. Contains seals, brake grease, spring and piston. PS12 handlebar master cylinder fitted to early 850 and 1000 models. PS12 rear master cylinder fitted to Nevada 750

This seal kit is also known as 082039797. NB repair kit instructions refer to rear master cylinder. To fit this to a PS12 handlebar mounted cylinder you will need to punch the old piston out using a thin drift through the hole at the banjo bolt end of the master cylinder. Carefully note the order of the ring and washer as the piston comes out and replace with components from kit. Brembo no. 110279720. See this link for help with fitting this kit

 More than 5 in stock

 17659352 GU17659352 17 65 93 52
 1765 9352 1765.9352 17.65.93.52

Also fits Ducati 500 SL Pantah, Ducati 350/500 Twin GTV, Ducati 350/500 SL Pantah, Benelli 500 Quattro, Benelli 504 Sport, Benelli 250 2C, Benelli 900 Sei, Laverda Montjuic, Harris F1

Brembo rebuild kit for Brembo F05 (P5) calipers with 32mm pistons. Contains 2 bolts, all seals and brake grease

This caliper also known as P2 F05N, P32B and P32F.
This seal kit also known as Brembo ref. 120279910, also used on Benelli 504 Sport, 650 Al'Azzura, Ducati 500s, Laverda 500 Montjuich and Zeta (front) and Bimota DB1 and YB4 (rear).

Not suitable for P32 rear calipers fitted to 750T and Nevada 750 (1991-2001) - see BRA01723 for this model. Will not fit pistons on Grimeca F05 calipers.

 More than 5 in stock

 39659000 GU39659000 39 65 90 00
 3965 9000 3965.9000 39.65.90.00

Also fits Benelli 504 Sport, Benelli 250 TS, Ducati Pantah 500SL, 650 Al'Azzura, Ducati 500s, Laverda 500 Montjuich and Zeta (front) and Bimota DB1 and YB4

Brembo brake caliper rebuild kit for one P2 F08 (P8) caliper, contains 2 pairs of seals, O ring and 2 M10 bolts

This seal kit is for F08 calipers fitted to front of all these models. Also used on some Triumph Bonnevilles, MZs, Ducati 600 Pantah, 500 Pantah, 500 Sport Desmo, 500 GTV, 650 SL, 750 F1, 750 F1B, 750 Paso, 750 Sport, 900 MHR, 900 SS, 900 S2, 906 Paso, 100 R1, 100 S2 Desmo, Laverda Jota 1000 and Laverda 1200 Anniversary. Brembo ref. 120274110

See BRA10310 for less expensive replica kit

 More than 5 in stock

 14659000 GU14659000 14 65 90 00
 1465 9000 1465.9000 14.65.90.00

Also fits Benelli 354, Benelli Sei, Ducati 250/350/450 Desmo (-1976), Ducati Pantah, Ducati F1, Ducati 750 Paso (1987-1990), Ducati 750 Sport (1988-1990), Ducati 860 GT/GTS, Ducati 900 GTS, Ducati Hailwood Rep, Ducati 900 Darmah (1977-1978), Ducati 906 Paso (1988-1989), Ducati 1000 R1 Hailwood Ref., Hesketh, Horex HRD 600, Horex 500/600 Columbus, Laverda 750 SF2, Laverda 750 SFC, Laverda 750 SF3, Laverda 1000 3C (1974-1978), Laverda 1000 3CL (1976-1981), Laverda 1000 RGS/RGA, Laverda 1000 SFC, Laverda 1200 (1978-1979), Laverda 1200 TS/Mirage (1981), MZ ETZ 125/150/250/300 (1985-1992), Norton Classic (1989), Norton Interpol (1989), Triumph T140 (1985-1988 Brembo)

Brembo caliper cover for models with obsolete twin bleed calipers

P9 caliper cover includes cutout each side for bleed nipple. Also known as Guzzi ref. 14654700, 17654760. Please note you may need to trim away the four moulded lugs at the bottom of the cover otherwise these may clash with your pad pins

 More than 5 in stock

 20325410 GU20325410 20 32 54 10
 2032 5410 2032.5410 20.32.54.10

99cm length of black pipe with clips for connecting rear master cylinder to brake fluid reservoir

Brake fluid, oil and fuel resistant. This is long enough for the rear brake master cylinder on V50 II and V35 I

 More than 5 in stock

The innovative Stahlbus bleeder valve allows you to change the brake fluid yourself without assistance. Suitable for models with two bleed nipples per caliper

Linked Guzzi brake systems are notoriously tricky to bleed, this M6 auto bleed nipple can save you hours of tedious squeezing and pumping! This bleed nipple is slightly longer than the standard part so some thread will be left showing even when fully closed.

• Completely sealed by O-ring.
• Hydraulic system remains sealed even during the venting process.
• Reliable non-return function, thus one-man operation.
• System has been bled in minutes.
• Wear of the threads in the caliper is prevented (up and screwing down during the bleeding process).
• For all hydraulic systems such as brakes and clutches stahlbus brake bleed valve just replaces the existing vent screw.
• Tested under extreme conditions by TÃœV Rheinland.
  See BRA41652 for bleed valve cover

   More than 5 in stock

  [ CLOSE WINDOW ]
  [ CLOSE WINDOW ]

Brembo pad pin kit for Brembo F05 (P5) calipers. Contains one long pin, two short and retaining spring

Brembo ref. 120280010, also used on some Laverdas . Front calipers only on Strada

 More than 5 in stock

 39659100 GU39659100 39 65 91 00
 3965 9100 3965.9100 39.65.91.00

Also fits Benelli 250 TS

Brake caliper rebuild kit for one P2 F08 (P8) caliper, contains 2 pairs of seals and O ring to seal the two halves together

This seal kit is for F08 calipers fitted to front of all these models. Also used on some Triumph Bonnevilles, MZs, Ducati 600 Pantah, 500 Pantah, 500 Sport Desmo, 500 GTV, 650 SL, 750 F1, 750 F1B, 750 Paso, 750 Sport, 900 MHR, 900 SS, 900 S2, 906 Paso, 100 R1, 100 S2 Desmo, Laverda Jota 1000 and Laverda 1200 Anniversary. Brembo ref. 120274110

 More than 5 in stock

 14659000 GU14659000 14 65 90 00
 1465 9000 1465.9000 14.65.90.00

Also fits Benelli 354, Benelli Sei, Ducati 250/350/450 Desmo (-1976), Ducati Pantah, Ducati F1, Ducati 750 Paso (1987-1990), Ducati 750 Sport (1988-1990), Ducati 860 GT/GTS, Ducati 900 GTS, Ducati Hailwood Rep, Ducati 900 Darmah (1977-1978), Ducati 906 Paso (1988-1989), Ducati 1000 R1 Hailwood Ref., Hesketh, Horex HRD 600, Horex 500/600 Columbus, Laverda 750 SF2, Laverda 750 SFC, Laverda 750 SF3, Laverda 1000 3C (1974-1978), Laverda 1000 3CL (1976-1981), Laverda 1000 RGS/RGA, Laverda 1000 SFC, Laverda 1200 (1978-1979), Laverda 1200 TS/Mirage (1981), MZ ETZ 125/150/250/300 (1985-1992), Norton Classic (1989), Norton Interpol (1989), Triumph T140 (1985-1988 Brembo)

Pair of organic EBC FA244 front brake pads for P4 30/34 F calipers with two pad pins (Brembo 6800 and 9970 calipers)

Guzzi pad reference is 01654630. Also fitted to some pre 2001 Cali EV's - check how many pins your brake caliper has if ordering for a 1997-2001 Cali EV. Also known as Guzzi ref. 2B003313, 61340211A, 01654630, 07670810, 07BB1935, AP8133614, 883673, 2B005736

 More than 5 in stock

 32654610 GU32654610 32 65 46 10
 3265 4610 3265.4610 32.65.46.10

Pair of EBC FA181TT rear brake pads

Also known as Guzzi ref. 30654626

 More than 5 in stock

05654630-z 05654630 GU05654630 05 65 46 30
 0565 4630 0565.4630 05.65.46.30

Also fits Royal Enfield Himalayan (Front)