The BoosterPlug is an effective and cost efficient way to cure the fuelling problems common to all modern fuel injected Guzzi's.
Plugging directly into the wiring harness using original connectors, with no cutting or splicing required, installation takes less than ten minutes.

The BoosterPlug features a unique technology to provide your bike with a controlled fuel enrichment in all ambient temperature situations. No other Plug and Play device does this. A richer mixture is provided only when needed i.e at low RPMs and when accelerating. On open roads at a constant speed the Boosterplug sits idle to keep fuel consumption low.
Make your bike run as it should have done from the factory!

• Improved and gentler throttle action when opening and closing throttle
• Richer mixture when opening the throttle improves acceleration
• Booster plug removes the uneven low speed running that is typical for modern lean burn engines
• Stronger and more consistent at idle.
• Reduced backfiring with aftermarket exhausts on engine braking
• Lifetime warranty

 This part is due back in stock soon, call 01484 841395 to reserve yours

A set of 6 x titanium hex head brake disc bolts for front discs on all models except V7 III and V7 850 where you will need 2 kits (to cover front and rear) or 3 kits for V85TT and V100 where they are also used front and rear.

Also known as Guzzi ref. 03611445 2B009221 and 2B002416. 1 kit required per disc. Some models use shorter FRA81285 which is M8 x 16- checks parts book for exact listing.
Tensile strength of these bolts is 950 - 970Mpa.
Ideal for replacing standard disc bolts which corrode and have soft heads. These Ti bolts will look great for a very long time!

AP8152286

Dimensions:
M8 x 20mm

Rocker cover screw kit containing 12 replacement stainless steel socket cap bolts for two valve small twin rocker covers. Only one kit required per engine. Only for twin throttle body V7 models

To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070). This kit is for models without billet rocker cover protectors fitted. This kit contains the correct screws for the Breva 750 and 2004 on V7 models but does not include the two flanged M5 screws SSA81523 that fasten the rocker cover covers to the rocker cover (on models other than the V7 Racer)

Dimensions:
M6 screws

Kit containing 8 long titanium shouldered retaining screws for your rocker covers. Upgrades the poor quality OE screws with shiny Ti parts

Rocker cover bolt kit for single throttle body models. Upgrade your corrosion prone zinc OE parts with a polished upgrade.

 887483 MG887483

Dimensions:
M6 x 50mm

Grey Moto Guzzi sticker featuring the Guzzi eagle. Perfect for mudguards, tanks, screens and anywhere else that will take a sticker.

Grey oval sticker with black border. Ideal for covering up marks on bodywork!

Dimensions:
62mm x 28mm

Titanium shouldered retaining screw for rocker cover. 4 required for each cylinder head

Rocker cover bolt for single throttle body models. Upgrade your corrosion prone zinc OE parts with a polished upgrade.

 887483 MG887483

Dimensions:
M6 x 50mm

Replacement blue LED in chrome bezel for Gutsibits clock surrounds ACA01001 and ACA01002

These 12v LEDs include a resistor, wires should be soldered to the mini spade connectors on the base of the LED

Dimensions:
8mm body OD, 29mm overall

Replacement green LED in chrome bezel for Gutsibits clock surrounds ACA01001 and ACA01002

These 12v LEDs include a resistor, wires should be soldered to the mini spade connectors on the base of the LED

Dimensions:
8mm body OD, 29mm overall

Aluminium pannier adapter plate, this bolts to the pannier rail or frame for the pannier to lock to

May be supplied in silver or black finish. These are normally included with panniers

Dimensions:
31mm x 61mm

Black plastic front mudguard extension or Fenda Extenda. This will protect the exhaust pipes and front engine cover on your Guzzi from road debris, salt, water and traffic grime thrown up by your front wheel

Specifically designed to follow the contour of your bike's front guard, our Extenda Fenda is supplied with both plastic rivets for mechanical fitment and a sheet of our specially sourced 'Stick Fit Pads' for those customers who would prefer not to drill their front mudguard. Our Extenda Fenda is simple to install and will arrive safely packaged, together with comprehensive fitting instructions and all necessary fittings as detailed above. See this video for help fitting yours