Roller tappet kit C for converting your 4 valve per cylinder model to the later rollerised tappets

All 4v/cyl 1200 Sport models use this kit.

For Griso and Stelvio your engine will need inspecting to work out which kit is required, this cannot be deduced from engine or chassis number. Further information about which kit you may need can be found here.
For this kit see Moto Guzzi factory bulletin no.02 from 2014. We recommend that you also get your fuelling map updated following this upgrade for maximum benefit

 Availability varies on this part, call us to check availability

If you would like to be emailed once this item is available again then click here

1A002082

Gear lever

 This part is due back in stock soon, call 01484 841395 to reserve yours

If you would like to be emailed once this item is available again then click here

 06250900 GU06250900 06 25 09 00
 0625 0900 0625.0900 06.25.09.00

Satin finish stainless steel conical silencer with conical end cap. Developed by Mistral for maximum performance using their in-house dyno. Hand made to order on the shores of Lake Como. Easy to install using existing mounting points.

As well as looking and sounding better than the stock silencer this performance exhaust is 2.3kg lighter and offers a useful increase in power and torque.
See this video to hear this silencer

To achieve maximum performance gains also fit link pipe EXA85629, velocity stack EXA85901 and performance air filter SIA10433 with V-Twin boost plug-in FUA85003
Benefits of Mistral silencers:

• Simple assembly
• Low weight
• No remap required
• EURO5+ approved
• Full and deep sound
• Specific bracket included
• Same position as the original exhaust: compatibility with side bags and Guzzi accessories
• Specific carbon fiber heat shield included
• Handcrafted product

 This part is available by special order, request a quote

Clutch cable

Also known as Guzzi ref. 883943. We advise you to measure your existing cable before ordering in case you have a non standard set up.

 This part is due back in stock soon, call 01484 841395 to reserve yours

If you would like to be emailed once this item is available again then click here

 32093010 GU32093010 32 09 30 10
 3209 3010 3209.3010 32.09.30.10

Dimensions:
1070mm outer length, 144mm free length, 9.3mm barrel nipple, 9.9mm barrel nipple

Brand new left hand original "Lego" type switchgear with switches for indicators, flash, horn, high / low beam and park. Previously unavailable new and ideal for your restoration project.

Comes with unattached 12 pin molex connector, rubber boot and pins ready for you to wire into your existing loom.

Dimensions:
670mm lead

UFI 25 531 00 cartridge oil filter for 1989 on small block engines. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick, If this item is out of stock we do stock a like for like replacement, which is this item SIA27301 .

For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer). Some 750 XPA models use SIA19530, we advise you to check your old filter before ordering. Also known as Guzzi ref. 2A000633

 27153085 GU27153085 27 15 30 85
 2715 3085 2715.3085 27.15.30.85

Dimensions:
120mm x 45mm diameter overall

UFI 30 989 00 flat type air filter, paper filament in rubber surround

See SIA30361 for a reusable K & N air filter

 30113600 GU30113600 30 11 36 00
 3011 3600 3011.3600 30.11.36.00

Dimensions:
220mm x 135mm x 35mm

Premium softstyle black T-shirt printed with classic Moto Guzzi logo in white on the chest.

Rear of shirt features our 'What do you mean you've only got one neutral'?! design - Guzzi riders know all about this!

Sizing:

• M fits 38 - 40" chest
• L fits 42 - 44" chest
• XL fits 46 - 48" chest
• XXL fits 50 - 52" chest

Steering damper in black finish

Fits to original frame bracket

14530201-z 14530201 GU14530201 14 53 02 01
 1453 0201 1453.0201 14.53.02.01

Dimensions:
9mm ID mounts, 168mm centres minimum, 250mm centres fully extended

Brembo brake master cylinder overhaul kit for handlebar, undertank (cable operated) mounted, handlebar mounted and rear PS 12 master cylinders. Contains seals, brake grease, spring and piston. PS12 handlebar master cylinder fitted to early 850 and 1000 models. PS12 rear master cylinder fitted to Nevada 750

This seal kit is also known as 082039797. NB repair kit instructions refer to rear master cylinder. To fit this to a PS12 handlebar mounted cylinder you will need to punch the old piston out using a thin drift through the hole at the banjo bolt end of the master cylinder. Carefully note the order of the ring and washer as the piston comes out and replace with components from kit. Brembo no. 110279720. See this link for help with fitting this kit

 17659352 GU17659352 17 65 93 52
 1765 9352 1765.9352 17.65.93.52

Also fits Ducati 500 SL Pantah, Ducati 350/500 Twin GTV, Ducati 350/500 SL Pantah, Benelli 500 Quattro, Benelli 504 Sport, Benelli 250 2C, Benelli 900 Sei, Laverda Montjuic, Harris F1

Dimensions:
Solid piston 12.7mm OD x 65mm