Clutch cable.
Fits Nevada 750 models with frame prefix ZGULMM. We advise you to measure your existing cable before ordering in case you have a non standard set up.
1 in stock
B063427
£25.00
INC VAT
£20.83 EX VAT
Oil pressure sender, M12 thread, male bullet connector
Supercedes Guzzi no. 12768700. Some small twins also require adapter 19055800 (or ELA19720 can be fitted in place of this switch). Check which type your small twin uses before replacing.
See ENA12640 for replacement crush washer if required
More than 5 in stock
17768750 GU17768750 17 76 87 50
1776 8750 1776.8750 17.76.87.50
£10.00
INC VAT
£8.33 EX VAT
Locking fuel filler cap, supplied with two keys and rubber seal
Does not fit early V7 Sport tanks with 54mm aperture
This part is due back in stock soon, call 01484 841395 to reserve yours
30103960-z 30103960 GU30103960 30 10 39 60
3010 3960 3010.3960 30.10.39.60
Also fits Ducati 600 SL Pantah, Ducati 900 MHR, S2, Ducati 900 MHR-I, Triumph T140 (Meriden), Laverda Montjuich
£85.00
INC VAT
£70.83 EX VAT
Rubber for rear fuel tank mounting
1 in stock
AP8120557
Also fits Aprilia 125, Aprilia 50 RS
£16.00
INC VAT
£13.33 EX VAT
Pipercross high performance air filter. Benefits of a Pipercross moulded panel motorcycle filter:
Pipercross, based in the UK home of motorsport have over 30 years of road and track racing experience when it comes to filtration. Through this experience and engineering only the highest quality is achieved which is passed onto you through more power, torque, fuel economy & throttle response. Why settle for lesser filter brands which only have road experience when you can have quality proven on the track?
2 in stock
AP8104329
£42.00
INC VAT
£35.00 EX VAT
Stainless steel exhaust cover for the exhaust link pipe and CAT. Fits easily to the standard exhaust system to improve the styling of the V100. This brushed stainless finish cover also helps shield your feet from the heat of the CAT. Note that this accessory is not compatible with a centre stand.
A quality accessory hand made in Italy for your V100
1 in stock
£60.00
INC VAT
£50.00 EX VAT
Kit containing 2 stainless steel M10 banjo bolts for Brembo brake fittings with copper washers
Supplied with 4 crush washers. Also known as Guzzi ref. 95990033
This part is due back in stock soon, call 01484 841395 to reserve yours
95990028-z 95990028 GU95990028 95 99 00 28
9599 0028 9599.0028 95.99.00.28
Also fits Laverda Jota
£8.40
INC VAT
£7.00 EX VAT
Cush drive rubber set
Set of 6 rubbers
This part is available by special order, request a quote
32632510
£82.00
INC VAT
£68.33 EX VAT
Complete twin bleed F09 (P9) front left hand (when mounted behind fork leg, otherwise use as RH) replica Brembo brake caliper. Also rear caliper (when mounted above and behind rear wheel spindle). Supplied with bleed nipples, dust cover, pins and spring. This can replace the P9 rear caliper as fitted to a 1000 SP, or can be used as a performance upgrade to replace the smaller piston P8 caliper fitted as standard to many Guzzis. Please see Guzziology for advice on how to perform this conversion.
Brake pads not included- see BRA33204
Availability varies on this part, check availability
£145.00
INC VAT
£120.83 EX VAT
Fork seal
3 in stock
30532861 GU30532861 30 53 28 61
3053 2861 3053.2861 30.53.28.61
£8.90
INC VAT
£7.42 EX VAT