Pair of wind deflectors in a matte finish, these fix to to your fuel tank behind the headstock to reduce buffeting at speed.

Supplied as a handed pair with black flanged screws to fitting.

 More than 5 in stock

Special tool for tightening and untightening the dipstick on small twins. The dipstick can be awkward to undo on these models but this tool makes it simple and quick. No more struggling to grip it or resorting to pliers, just use our tool.

Oil filler tool manufactured from PETG filament these are fully recyclable but as strong as ABS. Dipstick spanner 3D printed in the UK

 More than 5 in stock

 14927001 GU14927001 14 92 70 01
 1492 7001 1492.7001 14.92.70.01

UFI 25 531 00 cartridge oil filter for 1989 on small block engines. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick

For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer). Some 750 XPA models use SIA19530, we advise you to check your old filter before ordering. Also known as Guzzi ref. 2A000633

 More than 5 in stock

 27153085 GU27153085 27 15 30 85
 2715 3085 2715.3085 27.15.30.85

UFI 25 46 500 cartridge oil filter. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick

For post 1989 V35, V50 and V65 models use SIA27300 .
NB Packaging may vary. For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer)

 More than 5 in stock

 19153000 GU19153000 19 15 30 00
 1915 3000 1915.3000 19.15.30.00

Oil pressure sender, M12 thread, male bullet connector

Supercedes Guzzi no. 12768700. Some small twins also require adapter 19055800 (or ELA19720 can be fitted in place of this switch). Check which type your small twin uses before replacing.

See ENA12640 for replacement crush washer if required

 More than 5 in stock

 17768750 GU17768750 17 76 87 50
 1776 8750 1776.8750 17.76.87.50

Oil pressure switch. May be supplied with a vertical spade connector, this supercedes the original Guzzi part which is no longer available. This version will fit without removal of the alternator

See ENA12640 for replacement crush washer and ELA10005 for female spade connector

 2 in stock

 31768780 GU31768780 31 76 87 80
 3176 8780 3176.8780 31.76.87.80

Fine thread screw in brakelight switch for linked system proportioning valve or splitter. See ELA12735 for rubber cap

Stop light switch also known as Guzzi ref. 63657000

 3 in stock

 79654116 GU79654116 79 65 41 16
 7965 4116 7965.4116 79.65.41.16

Also fits Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 GT/Sport Köwe, Ducati 750 Paso (1984-1992), Ducati 750 Sport, Ducati 750/900 SS Köwe, Ducati 750 F1/Laguna Seca, Ducati 860/900 GTS, Ducati 900 Darmah, Ducati 900 MHR-I, Ducati 900 SS (1990), Ducati 906 Paso (1988), Ducati 1000 MHR-2/S2

Rear hugger finished in matte black, this will protect your rear shock from road spray and grit. Mounts via three pre drilled holes and supplied brackets

Similar matte finish to front mudguard MUA00244 .
Supplied with brackets and fasteners. See here for fitting instructions. Fitment of this hugger requires some mechanical skill- if in doubt please entrust this job to a professional

 1 in stock

Black plastic front mudguard extension or Fenda Extenda. This will protect the exhaust pipes and front engine cover on your Guzzi from road debris, salt, water and traffic grime thrown up by your front wheel

Specifically designed to follow the contour of your bike's front guard, our Extenda Fenda is supplied with both plastic rivets for mechanical fitment and a sheet of our specially sourced 'Stick Fit Pads' for those customers who would prefer not to drill their front mudguard. Our Extenda Fenda is simple to install and will arrive safely packaged, together with comprehensive fitting instructions and all necessary fittings as detailed above. See this video for help fitting yours

 2 in stock

Black plastic front mudguard extension or Fenda Extenda. This will protect the exhaust pipes and front engine cover on your Guzzi from road debris, salt, water and traffic grime thrown up by your front wheel

Specifically designed to follow the contour of your bike's front guard, our Extenda Fenda is supplied with both plastic rivets for mechanical fitment and a sheet of our specially sourced 'Stick Fit Pads' for those customers who would prefer not to drill their front mudguard. Our Extenda Fenda is simple to install and will arrive safely packaged, together with comprehensive fitting instructions and all necessary fittings as detailed above. See this video for help fitting yours

 2 in stock