High quality German made Mahle OE quality cartridge oil filter with sealing rubber.
From late 2015 onwards 1200 models used SIA06428
Please note that Daytona 1000 models where filter screws into base of sump require SIA14530. This is a 14 sided oil filer which is compatible with our oil filter tools TOA41005 and TOA01200. This Mahle filter is shorter that the equivalent UFI filter. See ENA90948 for the oil filter cover o ring
More than 5 in stock
30153000 GU30153000 30 15 30 00
3015 3000 3015.3000 30.15.30.00
£9.25
INC VAT
£7.71 EX VAT
Pair of wind deflectors in a matte finish, these fix to to your fuel tank behind the headstock to reduce buffeting at speed.
Supplied as a handed pair with black flanged screws to fitting.
More than 5 in stock
£20.00
INC VAT
£16.67 EX VAT
Special tool for tightening and untightening the dipstick on small twins. The dipstick can be awkward to undo on these models but this tool makes it simple and quick. No more struggling to grip it or resorting to pliers, just use our tool.
Oil filler tool manufactured from PETG filament these are fully recyclable but as strong as ABS. Dipstick spanner 3D printed in the UK
More than 5 in stock
14927001 GU14927001 14 92 70 01
1492 7001 1492.7001 14.92.70.01
£12.00
INC VAT
£10.00 EX VAT
UFI 25 531 00 cartridge oil filter for 1989 on small block engines. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick
For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer). Some 750 XPA models use SIA19530, we advise you to check your old filter before ordering. Also known as Guzzi ref. 2A000633
More than 5 in stock
27153085 GU27153085 27 15 30 85
2715 3085 2715.3085 27.15.30.85
£9.50
INC VAT
£7.92 EX VAT
UFI 25 46 500 cartridge oil filter. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick
For post 1989 V35, V50 and V65 models use SIA27300 .
NB Packaging may vary. For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer)
More than 5 in stock
19153000 GU19153000 19 15 30 00
1915 3000 1915.3000 19.15.30.00
£8.50
INC VAT
£7.08 EX VAT
Oil pressure sender, M12 thread, male bullet connector
Supercedes Guzzi no. 12768700. Some small twins also require adapter 19055800 (or ELA19720 can be fitted in place of this switch). Check which type your small twin uses before replacing.
See ENA12640 for replacement crush washer if required
More than 5 in stock
17768750 GU17768750 17 76 87 50
1776 8750 1776.8750 17.76.87.50
£10.00
INC VAT
£8.33 EX VAT
Oil pressure switch. May be supplied with a vertical spade connector, this supercedes the original Guzzi part which is no longer available. This version will fit without removal of the alternator
See ENA12640 for replacement crush washer and ELA10005 for female spade connector
2 in stock
31768780 GU31768780 31 76 87 80
3176 8780 3176.8780 31.76.87.80
£11.00
INC VAT
£9.17 EX VAT
Fine thread screw in brakelight switch for linked system proportioning valve or splitter. See ELA12735 for rubber cap
Stop light switch also known as Guzzi ref. 63657000
3 in stock
79654116 GU79654116 79 65 41 16
7965 4116 7965.4116 79.65.41.16
Also fits Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 GT/Sport Köwe, Ducati 750 Paso (1984-1992), Ducati 750 Sport, Ducati 750/900 SS Köwe, Ducati 750 F1/Laguna Seca, Ducati 860/900 GTS, Ducati 900 Darmah, Ducati 900 MHR-I, Ducati 900 SS (1990), Ducati 906 Paso (1988), Ducati 1000 MHR-2/S2
£21.40
INC VAT
£17.83 EX VAT
Rear hugger finished in matte black, this will protect your rear shock from road spray and grit. Mounts via three pre drilled holes and supplied brackets
Similar matte finish to front mudguard MUA00244 .
Supplied with brackets and fasteners. See here for fitting instructions. Fitment of this hugger requires some mechanical skill- if in doubt please entrust this job to a professional
1 in stock
£155.00
INC VAT
£129.17 EX VAT
Black plastic front mudguard extension or Fenda Extenda. This will protect the exhaust pipes and front engine cover on your Guzzi from road debris, salt, water and traffic grime thrown up by your front wheel
Specifically designed to follow the contour of your bike's front guard, our Extenda Fenda is supplied with both plastic rivets for mechanical fitment and a sheet of our specially sourced 'Stick Fit Pads' for those customers who would prefer not to drill their front mudguard. Our Extenda Fenda is simple to install and will arrive safely packaged, together with comprehensive fitting instructions and all necessary fittings as detailed above. See this video for help fitting yours
2 in stock
£22.50
INC VAT
£18.75 EX VAT