The innovative stahlbus bleeder valve allows you to change the brake fluid yourself without assistance. You may find it helpful to fit this valve to the proportioning valve or manifold on your Guzzi. M10 bleed screw used only on rear of 2003 on models
Linked Guzzi brake systems are notoriously tricky to bleed, this special bleed nipple can save you hours of tedious squeezing and pumping!
More than 5 in stock
£26.50
INC VAT
£22.08 EX VAT
The innovative stahlbus bleeder valve allows you to change the brake fluid yourself without assistance.
Linked Guzzi brake systems are notoriously tricky to bleed, this special bleed nipple can save you hours of tedious squeezing and pumping! This banjo bolt can be used in place of a standard fine thread M10 banjo bolt. Supplied with crush washers. We recommend fitting one of these brake valves per caliper
The innovative stahlbus vent valve allows you to change the brake fluid easily and without help. Clean, totally safe and fast !
This auto bleed valve combines all these advantages:
3 in stock
£33.00
INC VAT
£27.50 EX VAT
The innovative Stahlbus bleeder valve allows you to change the brake fluid yourself without assistance. Suitable for models with two bleed nipples per caliper
Linked Guzzi brake systems are notoriously tricky to bleed, this M6 auto bleed nipple can save you hours of tedious squeezing and pumping! This bleed nipple is slightly longer than the standard part so some thread will be left showing even when fully closed.
More than 5 in stock
£26.50
INC VAT
£22.08 EX VAT
The innovative stahlbus bleeder valve allows you to change the brake fluid yourself without assistance. You may find it helpful to fit this valve to the proportioning valve or manifold on your Guzzi. M10 bleed screw used only on rear of 2003 on models
Linked Guzzi brake systems are notoriously tricky to bleed, this special bleed nipple can save you hours of tedious squeezing and pumping!
More than 5 in stock
£26.50
INC VAT
£22.08 EX VAT
Inlet rubber with HT lead guide
Fits between exhaust manifold on cylinder head and carb. Use hose clip SSA45970. Suitable for PHF30 and PHF36 carbs
More than 5 in stock
14114350-z 14114350 GU14114350 14 11 43 50
1411 4350 1411.4350 14.11.43.50
£13.00
INC VAT
£10.83 EX VAT
Complete cast side stand with springs, pivot and mounting bracket finished in black. This stand is the original flip up / self retracting type
Bolts to engine mounting bolt at front of lower framerail, check that you have a long enough front engine mounting bolt for this sidestand to fit on to. This can be fitted to other Tonti frame models (e.g. Le Mans 1000). See FRA28162 for bracket that enables this stand to be mounted near the rider's footrest using the gearbox mounting bolt.
1 in stock
17432060-z 17432060 GU17432060 17 43 20 60
1743 2060 1743.2060 17.43.20.60
£99.00
INC VAT
£82.50 EX VAT
Throttle cable for models with standard high top PHF pumper carbs
We advise you to measure your existing cable before ordering in case you have a non standard set up.
4 in stock
14117555 GU14117555 14 11 75 55
1411 7555 1411.7555 14.11.75.55
£13.50
INC VAT
£11.25 EX VAT
Top end gasket and seal set containing rocker cover, base and head gaskets plus top end O rings
Top end gasket set for one cylinder. Inlet manifold gasket ENA14550 or ENA14500 and exhaust gasket ENA90718 available separately
More than 5 in stock
£14.40
INC VAT
£12.00 EX VAT
Rear hugger finished in matte black, this will protect your rear shock from road spray and grit. Mounts via three pre drilled holes and supplied brackets
Similar matte finish to front mudguard MUA00244 .
Supplied with brackets and fasteners. See here for fitting instructions. Fitment of this hugger requires some mechanical skill- if in doubt please entrust this job to a professional
1 in stock
£155.00
INC VAT
£129.17 EX VAT
Black plastic front mudguard extension or Fenda Extenda. This will protect the exhaust pipes and front engine cover on your Guzzi from road debris, salt, water and traffic grime thrown up by your front wheel
Specifically designed to follow the contour of your bike's front guard, our Extenda Fenda is supplied with both plastic rivets for mechanical fitment and a sheet of our specially sourced 'Stick Fit Pads' for those customers who would prefer not to drill their front mudguard. Our Extenda Fenda is simple to install and will arrive safely packaged, together with comprehensive fitting instructions and all necessary fittings as detailed above. See this video for help fitting yours
2 in stock
£22.50
INC VAT
£18.75 EX VAT