Polished Brembo aluminium brake lever
Also known as Guzzi ref. 10270652. Brembo ref. 110489431, AP8161262. Can be used instead of adjustable lever BRA81510 for Breva 1200, 1200 Sport, Norge etc... Replaces Guzzi ref. 2B003821 and 2B003041
1 in stock
03605645 GU03605645 03 60 56 45
0360 5645 0360.5645 03.60.56.45
£41.00
INC VAT
£34.17 EX VAT
New type clutch friction plate for models with deep splines with deep splined centre
2 plates required- thicker side of each friction plate should face transmission.
Also known as Guzzi ref. 30084410, 03084400, 29084450
V11 Tenni, Rosso Mandello and Scura have a single plate clutch which uses a different friction plate (unfortunately out of production)
These can be fitted to earlier 850 and 1000 models if the early shallow splined clutch centre is replaced with the later deep splined type. See our kit CLA20302 to update early 850/1000 models. Clutch plate alignment tool also available, see TOA30510
4 in stock
05084430 GU05084430 05 08 44 30
0508 4430 0508.4430 05.08.44.30
£57.70
INC VAT
£48.08 EX VAT
5 pin 12 volt relay suitable for starter, lights, indicator, flasher and horn applications
Supercedes Guzzi ref. 12732500. Equivalent to 28732500 but with mounting bracket
5 in stock
19732500-z 19732500 GU19732500 19 73 25 00
1973 2500 1973.2500 19.73.25.00
£15.20
INC VAT
£12.67 EX VAT
Round 12v two pin flasher relay
See FRA17720 for rubber mount
More than 5 in stock
17750520 GU17750520 17 75 05 20
1775 0520 1775.0520 17.75.05.20
£7.60
INC VAT
£6.33 EX VAT
Throttle cable with adjusting screw for models with Tommaselli 2C twistgrip
More than 5 in stock
17117500 GU17117500 17 11 75 00
1711 7500 1711.7500 17.11.75.00
£14.50
INC VAT
£12.08 EX VAT
Black clutch lever
See CLA17605 for this lever in aluminium finish. Can also be inverted for use as a brake lever on V50 II and V35 I with cable operated brake
1 in stock
14605750-z 14605750 GU14605750 14 60 57 50
1460 5750 1460.5750 14.60.57.50
£22.00
INC VAT
£18.33 EX VAT
Gearbox input seal and output shaft oil seal on big twins, fork seal on Nuovo Falcone. Used as crownwheel shaft oil seal on small twins. Output seal only on 4 speed gearboxes
Supercedes Guzzi ref. 90403547. Used as crownwheel carrier seal on small twins Also known as Guzzi ref. 90403549
More than 5 in stock
90403548 GU90403548 90 40 35 48
9040 3548 9040.3548 90.40.35.48
£18.50
INC VAT
£15.42 EX VAT
Dimensions:
10mm threaded shank, 11mm across flats, 8mm OD at base, 15mm from tip to underside of flats
Stainless steel M10 bleed nipple for Brembo single bleed P2 F08 (P8) calipers on pre 1998 models. This is the same length as the genuine Brembo part BRA17659. M10 bleed screw used only on rear of 2003 on models
Part of Guzzi ref. 17659260. Some brake calipers may require a longer bleed screw, we reecommend measuring your existing screw - it should be 15mm from under the flats to the base of the tip.
More than 5 in stock
£8.20
INC VAT
£6.83 EX VAT
A4 marine grade stainless steel M6 bleed nipple for Brembo F05 and twin bleed P2 F08 & F09 calipers. Manufactured specially for Gutsibits as a replica of the original Brembo M6 bleed nipple
Use M10 bleed screw SSA36794 for single bleed (later) P8 calipers. Ducati ref. 079539787
See BRA36794 for rubber cap
More than 5 in stock
Also fits Benelli 250 TS, Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 F1/Laguna Sec, KTM 250XC, KTM 250SX, KTM 250EXC,
£8.00
INC VAT
£6.67 EX VAT
Round 12v two pin flasher relay
See FRA17720 for rubber mount
More than 5 in stock
17750520 GU17750520 17 75 05 20
1775 0520 1775.0520 17.75.05.20
£7.60
INC VAT
£6.33 EX VAT