Final drive inner output seal

For Breva 750 from frame no. LL111908

 More than 5 in stock

90407591-z 90407591 GU90407591 90 40 75 91
 9040 7591 9040.7591 90.40.75.91

Steel intermediate clutch plate

 2 in stock

12082300-z 12082300 GU12082300 12 08 23 00
 1208 2300 1208.2300 12.08.23.00

Drive box input seal

Pinion oil seal

 More than 5 in stock

90403251-z 90403251 GU90403251 90 40 32 51
 9040 3251 9040.3251 90.40.32.51

Carb gasket kit / rebuild kit for 1 Dellorto PHF carb. Suitable for all PHF carbs with accelerator pumps including PHF36. Dellorto ref. 52514-77

Carb overhaul kit, float bowl seal FUA90001 and fuel filter FUA60888 also available separately to this carb seal kit

 More than 5 in stock

 14939950 GU14939950 14 93 99 50
 1493 9950 1493.9950 14.93.99.50

Also fits Hesketh, Laverda

Alternator belt

 1 in stock

 05702530 GU05702530 05 70 25 30
 0570 2530 0570.2530 05.70.25.30

Front brake master cylinder cap and rubber kit for Brembo PS 13 master cylinder. Check the screw holes in your master cylinder are diagnally opposed (as seen top left and bottom right corners when sitting on bike)

Reservoir cap replaces Guzzi ref. 2B001928

 1 in stock

 03661145 GU03661145 03 66 11 45
 0366 1145 0366.1145 03.66.11.45

Head Gasket

 5 in stock

 30022060 GU30022060 30 02 20 60
 3002 2060 3002.2060 30.02.20.60

A4 marine grade stainless steel M6 bleed nipple for Brembo F05 and twin bleed P2 F08 & F09 calipers. Manufactured specially for Gutsibits as a replica of the original Brembo M6 bleed nipple

Use M10 bleed screw SSA36794 for single bleed (later) P8 calipers. Ducati ref. 079539787

See BRA36794 for rubber cap

 More than 5 in stock

Also fits Benelli 250 TS, Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 F1/Laguna Sec, KTM 250XC, KTM 250SX, KTM 250EXC,

Pair of Brembo 07BB1408 carbon ceramic brake pads for Brembo P2 F08 (P8) calipers

For P08/F08 calipers. Front and rear pads for all models except P9 equipped Spada where these are only for front calipers

 4 in stock

28654601-z 28654601 GU28654601 28 65 46 01
 2865 4601 2865.4601 28.65.46.01

Also fits Benelli 354 Rear, Benelli Sei Fronts, Ducati 250/350/450 Desmo Fronts (-1976), Ducati Pantah, Ducati F1, Ducati 750 Paso Fronts (1987-1990), Ducati 750 Sport (1988-1990), Ducati 860 GT/GTS, Ducati 900 GTS, Ducati Hailwood Rep, Ducati 900 Darmah (1977-1978), Ducati 906 Paso (1988-1989), Ducati 1000 R1 Hailwood Ref., Hesketh, Horex HRD 600, Horex 500/600 Columbus, Laverda 750 SF2 Fronts, Laverda 750 SFC, Laverda 750 SF3, Laverda 1000 3C (1974-1978), Laverda 1000 3CL (1976-1981), Laverda 1000 RGS/RGA, Laverda 1000 RGS Corsa Rear, Laverda 1000 SFC, Laverda 1200 (1978-1979), Laverda 1200 TS/Mirage (1981), MZ ETZ 125/150/250/300 Fronts (1985-1992), Norton Classic (1989), Norton Interpol (1989), Triumph T140 (1985-1988 Brembo)

Single stainless steel M10 banjo bolt with bleed nipple for Brembo fittings. Supplied with bleed nipple cap and crush washers. Perfect for bleeding up old P9, F08 and F05 calipers where the bleed nipple has broken off. This can also be used to add additional bleed points to linked systems where airlocks are causing problems

These can be used to replace the standard banjo bolt on CARC models. See alternative part BRA41653 for Stahlbus auto bleed banjo bolt

 More than 5 in stock

Also fits Benelli 250 TS