Belt for Bosch generator

 1 in stock

12702505-z 12702505 GU12702505 12 70 25 05
 1270 2505 1270.2505 12.70.25.05

Head Gasket for square barrel models

 3 in stock

14022065-z 14022065 GU14022065 14 02 20 65
 1402 2065 1402.2065 14.02.20.65

UFI 25 531 00 cartridge oil filter for 1989 on small block engines. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick

For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer). Some 750 XPA models use SIA19530, we advise you to check your old filter before ordering. Also known as Guzzi ref. 2A000633

 More than 5 in stock

 27153085 GU27153085 27 15 30 85
 2715 3085 2715.3085 27.15.30.85

Pinion oil seal for rear drive box on small twins and rear wheel bearing oil seal for 850T

 More than 5 in stock

 90403247 GU90403247 90 40 32 47
 9040 3247 9040.3247 90.40.32.47

Lower throttle cable

We advise you to measure your existing cable before ordering in case you have a non standard set up

 2 in stock

12117501-z 12117501 GU12117501 12 11 75 01
 1211 7501 1211.7501 12.11.75.01

Full engine and gearbox seal kit, includes all necessary seals for a complete engine and gearbox overhaul.

Full gasket sets also available. Can also be fitted to models equipped with a Saprisa charging system if front crank oil seal ENA94238 is ordered

 More than 5 in stock

 17999550 GU17999550 17 99 95 50
 1799 9550 1799.9550 17.99.95.50

Set of 12 cush drive rubbers

Contains 12 rubbers, also known as Guzzi ref. 14336803

 1 in stock

 01336800 GU01336800 01 33 68 00
 0133 6800 0133.6800 01.33.68.00

Carb gasket kit / rebuild kit for Dellorto PHBH carbs

Carb overhaul kit, float bowl seal FUA90001, fuel filter FUA60888 and float bowl washer FUA27720 available separately to this carb seal kit

 More than 5 in stock

 19939980 GU19939980 19 93 99 80
 1993 9980 1993.9980 19.93.99.80

Dellorto choke piston or plunger for Dellorto VHB, PHBH, PHF and PHM carbs. Includes rubber seal in end of plunger

 More than 5 in stock

 13937800 GU13937800 13 93 78 00
 1393 7800 1393.7800 13.93.78.00

Brembo brake caliper rebuild kit for one P2 F08 (P8) caliper, contains 2 pairs of seals, O ring and 2 M10 bolts

This seal kit is for F08 calipers fitted to front of all these models. Also used on some Triumph Bonnevilles, MZs, Ducati 600 Pantah, 500 Pantah, 500 Sport Desmo, 500 GTV, 650 SL, 750 F1, 750 F1B, 750 Paso, 750 Sport, 900 MHR, 900 SS, 900 S2, 906 Paso, 100 R1, 100 S2 Desmo, Laverda Jota 1000 and Laverda 1200 Anniversary. Brembo ref. 120274110

See BRA10310 for less expensive replica kit

 More than 5 in stock

 14659000 GU14659000 14 65 90 00
 1465 9000 1465.9000 14.65.90.00

Also fits Benelli 354, Benelli Sei, Ducati 250/350/450 Desmo (-1976), Ducati Pantah, Ducati F1, Ducati 750 Paso (1987-1990), Ducati 750 Sport (1988-1990), Ducati 860 GT/GTS, Ducati 900 GTS, Ducati Hailwood Rep, Ducati 900 Darmah (1977-1978), Ducati 906 Paso (1988-1989), Ducati 1000 R1 Hailwood Ref., Hesketh, Horex HRD 600, Horex 500/600 Columbus, Laverda 750 SF2, Laverda 750 SFC, Laverda 750 SF3, Laverda 1000 3C (1974-1978), Laverda 1000 3CL (1976-1981), Laverda 1000 RGS/RGA, Laverda 1000 SFC, Laverda 1200 (1978-1979), Laverda 1200 TS/Mirage (1981), MZ ETZ 125/150/250/300 (1985-1992), Norton Classic (1989), Norton Interpol (1989), Triumph T140 (1985-1988 Brembo)