Carb gasket kit / rebuild kit for 1 Dellorto PHF carb. Suitable for all PHF carbs with accelerator pumps including PHF36. Dellorto ref. 52514-77
Carb overhaul kit, float bowl seal FUA90001 and fuel filter FUA60888 also available separately to this carb seal kit
More than 5 in stock
14939950 GU14939950 14 93 99 50
1493 9950 1493.9950 14.93.99.50
Also fits Hesketh, Laverda
£18.75
INC VAT
£15.62 EX VAT
Speedo sensor with 100cm lead and 3 pin plug for non ABS equipped models
1 in stock
AP8124985
£252.00
INC VAT
£210.00 EX VAT
Silencer clamp gasket / shim or muffler gasket used to seal crossover to silencer
This exhaust bush is not required if a Mistral or Agostini silencer is fitted
1 in stock
05128230 GU05128230 05 12 82 30
0512 8230 0512.8230 05.12.82.30
£25.00
INC VAT
£20.83 EX VAT
Complete LED indicator with lead. Fits front right or rear left
1 in stock
2D000439
£45.00
INC VAT
£37.50 EX VAT
49cm length of black pipe with clips for connecting rear master cylinder to brake fluid reservoir
Brake fluid, oil and fuel resistant. We recommend measuring your existing pipe first to check ensure this 49cm pipe will be long enough. This is not long enough for the rear brake master cylinder on V50 II and V35 I
More than 5 in stock
£8.80
INC VAT
£7.33 EX VAT
Single stainless steel M10 banjo bolt with bleed nipple for Brembo fittings. Supplied with bleed nipple cap and crush washers. Perfect for bleeding up old P9, F08 and F05 calipers where the bleed nipple has broken off. This can also be used to add additional bleed points to linked systems where airlocks are causing problems
These can be used to replace the standard banjo bolt on CARC models. See alternative part BRA41653 for Stahlbus auto bleed banjo bolt
More than 5 in stock
Also fits Benelli 250 TS
£21.00
INC VAT
£17.50 EX VAT
Pinion oil seal for rear drive box on small twins and rear wheel bearing oil seal for 850T
More than 5 in stock
90403247 GU90403247 90 40 32 47
9040 3247 9040.3247 90.40.32.47
£10.50
INC VAT
£8.75 EX VAT
UFI 25 46 500 cartridge oil filter. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick
For post 1989 V35, V50 and V65 models use SIA27300 .
NB Packaging may vary. For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer)
More than 5 in stock
19153000 GU19153000 19 15 30 00
1915 3000 1915.3000 19.15.30.00
£8.50
INC VAT
£7.08 EX VAT
Oil pressure switch. May be supplied with a vertical spade connector, this supercedes the original Guzzi part which is no longer available. This version will fit without removal of the alternator
See ENA12640 for replacement crush washer and ELA10005 for female spade connector
5 in stock
31768780 GU31768780 31 76 87 80
3176 8780 3176.8780 31.76.87.80
£11.00
INC VAT
£9.17 EX VAT
Rotational oil seal for crownwheel carrier in drive box on post 1974 big twins. Front crank oil seal on loop frame models
Also known as Guzzi ref. 90403850 and used on 850 GT and loop frame models for front crank oil seal ( 90403851 )
More than 5 in stock
90413850 GU90413850 90 41 38 50
9041 3850 9041.3850 90.41.38.50
£9.80
INC VAT
£8.17 EX VAT