Rubber rocker gasket for left hand cylinder. See ENA87742 for right hand side

 1 in stock

 872741 MG872741

Rubber rocker gasket for right hand cylinder. See ENA87741 for left hand side

 1 in stock

 872742 MG872742

Brembo brake caliper rebuild kit for one P2 F08 (P8) caliper, contains 2 pairs of seals, O ring and 2 M10 bolts

This seal kit is for F08 calipers fitted to front of all these models. Also used on some Triumph Bonnevilles, MZs, Ducati 600 Pantah, 500 Pantah, 500 Sport Desmo, 500 GTV, 650 SL, 750 F1, 750 F1B, 750 Paso, 750 Sport, 900 MHR, 900 SS, 900 S2, 906 Paso, 100 R1, 100 S2 Desmo, Laverda Jota 1000 and Laverda 1200 Anniversary. Brembo ref. 120274110

See BRA10310 for less expensive replica kit

 More than 5 in stock

 14659000 GU14659000 14 65 90 00
 1465 9000 1465.9000 14.65.90.00

Also fits Benelli 354, Benelli Sei, Ducati 250/350/450 Desmo (-1976), Ducati Pantah, Ducati F1, Ducati 750 Paso (1987-1990), Ducati 750 Sport (1988-1990), Ducati 860 GT/GTS, Ducati 900 GTS, Ducati Hailwood Rep, Ducati 900 Darmah (1977-1978), Ducati 906 Paso (1988-1989), Ducati 1000 R1 Hailwood Ref., Hesketh, Horex HRD 600, Horex 500/600 Columbus, Laverda 750 SF2, Laverda 750 SFC, Laverda 750 SF3, Laverda 1000 3C (1974-1978), Laverda 1000 3CL (1976-1981), Laverda 1000 RGS/RGA, Laverda 1000 SFC, Laverda 1200 (1978-1979), Laverda 1200 TS/Mirage (1981), MZ ETZ 125/150/250/300 (1985-1992), Norton Classic (1989), Norton Interpol (1989), Triumph T140 (1985-1988 Brembo)

Oil pressure sender, M12 thread, male bullet connector

Supercedes Guzzi no. 12768700. Some small twins also require adapter 19055800 (or ELA19720 can be fitted in place of this switch). Check which type your small twin uses before replacing.

See ENA12640 for replacement crush washer if required

 More than 5 in stock

 17768750 GU17768750 17 76 87 50
 1776 8750 1776.8750 17.76.87.50

Silencer clamp gasket / shim or muffler gasket used to seal crossover to silencer

This exhaust bush is not required if a Mistral or Agostini silencer is fitted

 1 in stock

 05128230 GU05128230 05 12 82 30
 0512 8230 0512.8230 05.12.82.30

Rear crankcase oil seal or rear main oil seal.

Fits Nevada 750 up to engine LT017877 and Nevada 350 to engine PC053625. Also known as Guzzi ref. 90405368. We recommend replacing the rear crank oil seal when replacing the clutch

 More than 5 in stock

90405367-z 90405367 GU90405367 90 40 53 67
 9040 5367 9040.5367 90.40.53.67

Rotational oil seal for crownwheel carrier in drive box on post 1974 big twins. Front crank oil seal on loop frame models

Also known as Guzzi ref. 90403850 and used on 850 GT and loop frame models for front crank oil seal ( 90403851 )

 More than 5 in stock

 90413850 GU90413850 90 41 38 50
 9041 3850 9041.3850 90.41.38.50

UFI 25 46 500 cartridge oil filter. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick

For post 1989 V35, V50 and V65 models use SIA27300 .
NB Packaging may vary. For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer)

 More than 5 in stock

 19153000 GU19153000 19 15 30 00
 1915 3000 1915.3000 19.15.30.00

Used in place of Guzzi ref. AP8125841

 2 in stock

AP8125773

Silent block rubber used in a variety of applications e.g. side stand rubber on V11 Sport and centre stand rubber on Stelvio

Rubber buffer for stands

 1 in stock

 93242015 GU93242015 93 24 20 15
 9324 2015 9324.2015 93.24.20.15