Roller tappet kit C for converting your 4 valve per cylinder model to the later rollerised tappets

All 4v/cyl 1200 Sport models use this kit.

For Griso and Stelvio your engine will need inspecting to work out which kit is required, this cannot be deduced from engine or chassis number. Further information about which kit you may need can be found here.
For this kit see Moto Guzzi factory bulletin no.02 from 2014. We recommend that you also get your fuelling map updated following this upgrade for maximum benefit

 This part is available by special order, request a quote

1A002082

Roller tappet kit B for converting your 4 valve per cylinder model to the later rollerised tappets

Your engine will need inspecting to work out which kit is required, this cannot be deduced from engine or chassis number. Further information about which kit you may need can be found here.
For this kit see Moto Guzzi factory bulletin no.02 from 2014. We recommend that you also get your fuelling map updated following this upgrade for maximum benefit

 This part is available by special order, request a quote

1A002063

Roller tappet kit A for converting your 4 valve per cylinder model to the later rollerised tappets

Your engine will need inspecting to work out which kit is required, this cannot be deduced from engine or chassis number. Further information about which kit you may need can be found here.
For this kit see Moto Guzzi factory bulletin no.20 from 2013. We recommend that you also get your fuelling map updated following this upgrade for maximum benefit

 This part is available by special order, request a quote

1A002060

Silicone rocker cover O ring for 4 valve small twins

 2 in stock

 27023780 GU27023780 27 02 37 80
 2702 3780 2702.3780 27.02.37.80

Pod type air filter for increased air flow

Made from a high performance twin layer foam this K & N type air filter is designed to offer improved and unrestricted airflow whilst offering adequate filtration. Washable and reusable (use hot soapy water). Best run dry for road. Fits VHB 24 and VHB 26 Dellorto carbs but your carbs must have the original gasket fitted to the rear of the carb, our part number ENA90763 - recommend fitting two to each carb. You may find that a 5-10% increase in main jet size helps to make the most of the increased air flow with this filter

 This part is available by special order, request a quote

Pod type air filter for increased air flow

Made from a high performance twin layer foam this K & N type air filter is designed to offer improved and unrestricted airflow whilst offering adequate filtration. Washable and reusable (use hot soapy water). Best run dry for road. Fits VHB 29, VHB 30, PHBH28 and PHBH30 Dellorto carbs. You may find that a 5-10% increase in main jet size helps to make the most of the increased air flow with this filter

 This part is available by special order, request a quote

Pod type air filter for increased air flow

Made from a high performance twin layer foam this K & N type air filter is designed to offer improved and unrestricted airflow whilst offering adequate filtration. Washable and reusable (use hot soapy water). Best run dry for road. Fits PHF 30 and PHF 36 Dellorto carbs. You may find that a 5-10% increase in main jet size helps to make the most of the increased air flow with this filter

 This part is available by special order, request a quote

Clamp on Pipercross foam air filter

This K & N foam air filter is designed to offer improved and unrestricted airflow whilst offering adequate filtration. Washable and reusable. Best run dry for road. Fits VHB 24 and VHB 26 Dellorto carbs. You may find that a 5-10% increase in main jet size helps to make the most of the increased air flow with this filter. Supercedes discontinued S & B air filters

 2 in stock

HIgh performance velocity stack for airbox to throttle body union. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body.

Mistral developed this performance modification usng 3D printing to benchmark various designs on a dyno until torque, power and throttle response were optimised. An extra + 1cv of power and + 1Nm of torque at 3500 RPM, increasing to a maximum of +2.3 cv and +3.5 Nm. The product is made of the next-generation polymers, installation is very simple and it does not require modifications to the bike.

 This part is available by special order, request a quote

NGK Iridium DR9EIX high performance spark plug

Due to the properties of Iridium, the spark plugs centre electrode can be made with a much smaller diameter than with platinum, Gold or gold palladium and copper/nickel types without sacrificing service life. See TOA00014 for spark plug spanner

 2 in stock