Shop headings: New Spares | Used Spares | Accessories | Brands
Woodruff key for oil pump shaft
This part is due back in stock soon, call 01484 841395 to reserve yours
13148300 GU13148300 13 14 83 00
1314 8300 1314.8300 13.14.83.00
£3.30
INC VAT
£2.75 EX VAT
Factory upgraded oil pump with 16mm wide teeth as fitted to later big twins. Gives increased flow and can be retro fitted to earlier 850/1000 models which originally had 14mm teeth pumps
This part is available by special order, request a quote
30146400 GU30146400 30 14 64 00
3014 6400 3014.6400 30.14.64.00
£245.00
INC VAT
£204.17 EX VAT
Length of pipe used for oil return and breather applications depending on model
Also known as Guzzi ref. 12157600. This pipe has an outside diameter slightly larger than the original so will not fit through the hose support bracket on some models
4 in stock
95985136 GU95985136 95 98 51 36
9598 5136 9598.5136 95.98.51.36
£7.80
INC VAT
£6.50 EX VAT
Cartridge oil filter UFI 23 149 00
Fits Daytona 1000 models where filter screws into base of sump. This is an 8 sided UFI filter.
Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump.
You may also require SIA10070 which is the crush washer for the drain plug and ENA14036 (sump gasket).
Please note that Daytona RS and T5 Polizia use filter SIA15300
More than 5 in stock
14153000 GU14153000 14 15 30 00
1415 3000 1415.3000 14.15.30.00
£10.50
INC VAT
£8.75 EX VAT
O ring used on cylinder head, gearbox input shaft and output shaft on big twins
Used in bevel box on small twins. Also known as Guzzi ref. 2A000270
More than 5 in stock
90706203 GU90706203 90 70 62 03
9070 6203 9070.6203 90.70.62.03
£1.00
INC VAT
£0.83 EX VAT
Black cylinder stud O ring
12 needed per big twin engine. 4 fitted per cylinder under rocker gear, 2 under barrel to seal top end oil ways. Can also be used as O rings on big twin distributor shaft. Also known as Guzzi ref. 90706090.
More than 5 in stock
90706094 GU90706094 90 70 60 94
9070 6094 9070.6094 90.70.60.94
£0.55
INC VAT
£0.46 EX VAT
Black O ring
Many applications including clutch pushrod plunger O ring at rear of gearbox
More than 5 in stock
90706170 GU90706170 90 70 61 70
9070 6170 9070.6170 90.70.61.70
£0.80
INC VAT
£0.67 EX VAT
Special nut for retaining crankshaft timing sprocket. Also used as clutch centre nut on V11 Sport
See TOA18651 for special tool to remove and tighten this nut. Nut also known as Guzzi ref. 93601025. See ENA92525 for correct part for series 2 Cali 1100s
This part is due back in stock soon, call 01484 841395 to reserve yours
93601026 GU93601026 93 60 10 26
9360 1026 9360.1026 93.60.10.26
£8.00
INC VAT
£6.67 EX VAT
Nut
Used as tappet adjuster nut on Tonti frame and 1100 Sport models, many other applications
4 in stock
10034100-z 10034100 GU10034100 10 03 41 00
1003 4100 1003.4100 10.03.41.00
£11.80
INC VAT
£9.83 EX VAT
Set of matt finished aluminium round barrel rocker covers (Guzzi ref. 17023550 or 17023560). Ideal for finishing off your restoration project
This rocker cover set is also known as Guzzi ref. 14023550, these can be fited to square barrel models if fitted with adapter kit ACA30310
This part is available by special order, request a quote
17023560 GU17023560 17 02 35 60
1702 3560 1702.3560 17.02.35.60
£285.00
INC VAT
£237.50 EX VAT