Red NGK spark plug resistor cap with rubbers

Also known as suppressor cap

 Sorry, this part is no longer available.

LD05F

Complete 12v 300w alternator for Saprisa charging systems

No longer in production

 Sorry, this part is no longer available.

 28712400 GU28712400 28 71 24 00
 2871 2400 2871.2400 28.71.24.00

Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.

Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear. Small block models will require an adapter to retain all the switch functions.

 This part is due back in stock soon, call 01484 841395 to reserve yours

 01738030 GU01738030 01 73 80 30
 0173 8030 0173.8030 01.73.80.30

Modern solid state electronic regulator for models with Bosch charging system

Bolts to original mounting point but this replacement part is not as tall as the old metal regulator. Also known as Guzzi ref. 17703800. Replaces ELA29704

See our Bosch fault finder page for help diagnosing problems on your Bosch charging system. The original type mechanical regulator is no loger available

 This part is due back in stock soon, call 01484 841395 to reserve yours

29703800-z 29703800 GU29703800 29 70 38 00
 2970 3800 2970.3800 29.70.38.00

Prolong battery life with this 9 stage smart battery charger, suitable for 6v, 12v AGM and lead acid batteries.

Weatherproof - suitable for use outside 6V / 12V 1A Auto-sensing charger. Suits all AGM, Lead Acid, Calcium and Gel batteries Charges 6v and 12v batteries Ring terminal and alligator clip harnesses included Spark proof Maintains full charge Simple, connect and wait for green light Overload / Short circuit protection See ACA96001 for a spare set of charging leads (e.g. for a separate bike).

 This part is due back in stock soon, call 01484 841395 to reserve yours

Alternator upgrade kit for Bosch systems containing stator windings, wound rotor and replacement diode board. The superior design alternator has an output up to 300% greater than the original Bosch system. You may wish to fit a plastic alternator spacer ENA18150 if your model does not have one of these already (to improve cooling of the alternator). You will need front crank seal ENA90428 (Bosch seal) if you wish to fit this to a bike with a Saprisa charging system. This kit reuses your existing Bosch regulator and stator plate with brush holder, see ELA29703 for a replacement regulator and ELA17452 for brush holders.

• Outputs 600W @5000 RPM
• Supplied with rotor removal tool
• For tapered crankshafts

1. Remove stator and rotor using the supplied rotor removal tool
2. Remove the old stator windings from the stator plate
3. Solder in the new stator widing wires to the connection block on the stator plate and reconnect the
4. Mount the replacement diode board, this should be protected from the weather but cooled by passing air
5. Connect up the system as follows: Terminals U,V and W take the three yellow wires which should be connected to the stator plate block; Y goes to Y on the stator plate; The brown wires go to earth (we recommend using some earth sleeve on these if possible); Red goes to the battery positive terminal; regulator wiring remains as before (D+ to diode board, D- to earth and DF to brush holder)
6. Check charge warning light is working (earth DF wire at stator to check bulb function)
7. Turn motor over by hand to ensure everything is seated correctly, there should be an air gap between the stator windings amd rotor
Fit alternator cover and spacer

 This part is available by special order, request a quote

Permanent replacement for unreliable condensers. This capacitor replaces both condensers with a single unit that should never need to be replaced

Earths through supplied bracket, can be mounted inside distributor. Fit and forget reliability. 1 required

 This part is due back in stock soon, call 01484 841395 to reserve yours

 14715433 GU14715433 14 71 54 33
 1471 5433 1471.5433 14.71.54.33

Brand new budget starter motor and solenoid suitable as a direct replacement for Guzzi Valeo and Bosch 8 or 9 teeth starter motors. You may need to fit hex headed neutral switch bolts on some pre 1990 models to make room for the solenoid. Our part number for the bolt is SSA06016 Please note that this item may be fitted to Loop frame models with some modifications as described in Guzziology, also see https://www.thisoldtractor.com/moto_guzzi_loopframe_starter_-_how_to_replace_the_magneti_marelli_starter_with_a_valeo.html for advice on this upgrade.

Supercedes Guzzi refs. 12730705, 14730554 and 14730705

Get a discount of £20 on this item if you part exchange your existing faulty Valeo or Bosch starter motor.

 This part is due back in stock soon, call 01484 841395 to reserve yours

 30730711 GU30730711 30 73 07 11
 3073 0711 3073.0711 30.73.07.11

Marelli condenser with cable and mount bracket

2 required

 This part is due back in stock soon, call 01484 841395 to reserve yours

 14715433 GU14715433 14 71 54 33
 1471 5433 1471.5433 14.71.54.33

Brakelight switch banjo bolt

See BRA01004 and BRA01014 for alternative universal stop light switch. Also known as Guzzi ref. 06261020, 000037891, 800037891, 079654114, 14657050

 This part is due back in stock soon, call 01484 841395 to reserve yours

 14657959 GU14657959 14 65 79 59
 1465 7959 1465.7959 14.65.79.59