Shop headings: New Spares | Used Spares | Accessories | Brands
Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with 12 volt 3 Ohm coils ELA14500 (big twins) and can be used to replace Digiplex on models with Ducati charging systems where the bike is converted to carburettors. This kit is just an ignition system, it will not control fuelling. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.
2 year warranty on Sachse ignition kits
Once fitted no further adjustment should be necessary. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. See this link for fitting instructions. Some bikes may need at least one additional spacer to allow enough clearance for alternator cover to fit once pickup is fitted. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA14500
This part is available by special order, request a quote
£395.00
INC VAT
£329.17 EX VAT
Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.
Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear. Small block models will require an adapter to retain all the switch functions.
This part is due back in stock soon, call 01484 841395 to reserve yours
01738030 GU01738030 01 73 80 30
0173 8030 0173.8030 01.73.80.30
£88.00
INC VAT
£73.33 EX VAT
Self adhesive cable tie block for securing cables to bodywork and panels, particularly useful where cables must be kept out of the way under the rear mudguard. Simply stick block to bodywork, route cable tie through bracket on block and round wiring
Wiring clip. One block
More than 5 in stock
£0.70
INC VAT
£0.58 EX VAT
Brakelight switch for handlebar mounted master cylinder
Stop light switch also known as Guzzi ref. 30530526. Please compare with your existing switch to check compatibility. Can be used as a substitute for ELA27815 or ELA30860. Sometimes supplied with three terminals, in this instance disregard middle terminal. Please note that terminals are smaller than standard switch and will need to be soldered on.
2 in stock
30749860 GU30749860 30 74 98 60
3074 9860 3074.9860 30.74.98.60
£13.50
INC VAT
£11.25 EX VAT
Brakelight switch for handlebar mounted master cylinder
Stop light switch also known as Guzzi ref. 30530526. Please compare with your existing switch to check compatibility. Can be used as a substitute for ELA27815. See ELA30861 for less expensive alternative part. Sometimes supplied with three terminals, in this instance disregard middle terminal
1 in stock
30749860 GU30749860 30 74 98 60
3074 9860 3074.9860 30.74.98.60
£17.60
INC VAT
£14.67 EX VAT
Ball bearing for brakelight switch
5 in stock
92295708 GU92295708 92 29 57 08
9229 5708 9229.5708 92.29.57.08
£0.90
INC VAT
£0.75 EX VAT
Brush kit for overhauling Bosch starter motor
The brush connections need to be soldered
This part is due back in stock soon, call 01484 841395 to reserve yours
£11.00
INC VAT
£9.17 EX VAT
Green 30A blade fuse
More than 5 in stock
28742562 GU28742562 28 74 25 62
2874 2562 2874.2562 28.74.25.62
£0.60
INC VAT
£0.50 EX VAT
Blue 15A blade fuse
More than 5 in stock
28742560 GU28742560 28 74 25 60
2874 2560 2874.2560 28.74.25.60
£0.60
INC VAT
£0.50 EX VAT
Brakelight switch banjo bolt
See BRA01004 and BRA01014 for alternative universal stop light switch. Also known as Guzzi ref. 06261020, 000037891, 800037891, 079654114, 14657050
2 in stock
14657959 GU14657959 14 65 79 59
1465 7959 1465.7959 14.65.79.59
£21.00
INC VAT
£17.50 EX VAT