Black cover or cap for Stahlbus M6 bleed valve. Prevents contamination of the valve and smartens up your brake caliper

 2 in stock

Universal hydraulic brake light switch. This hydraulic switch replaces discontinued brakelight switches by bolting in place of a single banjo bolt on the handlebar or rear brake master cylinder

NB stop light switch may be supplied with or without 2 pin block connector. Can be used in place of Guzzi ref. 32657060

 1 in stock

External return spring for rear brake master cylinder

Some models use 70mm spring FUA17667 for rear master cylinder - we recommend measuring yours before ordering

 1 in stock

 17667651 GU17667651 17 66 76 51
 1766 7651 1766.7651 17.66.76.51

Brembo PS 13 handlebar mounted front master cylinder. The PS13 has a small rectangular fluid reservoir

Replaces Guzzi refs 28660178 and 30660180. Supplied complete with black or polished lever. Uses switch ELA30860

 1 in stock

 28660278 GU28660278 28 66 02 78
 2866 0278 2866.0278 28.66.02.78

Front brake master cylinder cap and rubber kit for Brembo PS 13 / PS16 master cylinder. Screw holes parallel to top and bottom edges

Brembo ref. 110430860

 1 in stock

Also fits Ducati 907 i.e.

Rebuild kit for Brembo PS 13 handlebar mounted brake and clutch master cylinders, includes all seals, return spring and brake grease. Piston is hollow

This seal kit is for Cali 1100 master cylinders with a hollow pivot pin, does not fit early models with a solid pivot pin. For Cali EV models this only fits master cylinders with a pair of screws in the middle of the cap, it does not fit the later master cylinder which has diagonally opposed screws. Also know as Guzzi ref. 28659378, 000043851, 30659330. NB Included instructions may refer to rear master cylinder applications rather than front. Brembo ref. 110436250

 1 in stock

Also fits Cagiva Elefant E750, Ducati 748

Split pin for brake pedal pivot

 1 in stock

 95500227 GU95500227 95 50 02 27
 9550 0227 9550.0227 95.50.02.27

Clevis pin used in brake and gear change linkages, wears over time so well worth replacing on high mileage bikes

Replaces Guzzi refs. 95780265, 95780267, 95770265-Z, 95780265-Z. See BRA95227 for retaining split pin

 1 in stock

 95770265 GU95770265 95 77 02 65
 9577 0265 9577.0265 95.77.02.65

Universal hydraulic brakelight switch. This hydraulic switch replaces discontinued brake light switches by bolting in place of a double banjo bolt on the handlebar or rear brake master cylinder

Especially suitable for replacing the standard switch on models where the front brakes have been 'de-linked'

 1 in stock

The innovative stahlbus bleeder valve allows you to change the brake fluid yourself without assistance.

Linked Guzzi brake systems are notoriously tricky to bleed, this special bleed nipple can save you hours of tedious squeezing and pumping! This banjo bolt can be used in place of a standard fine thread M10 banjo bolt. Supplied with crush washers. We recommend fitting one of these brake valves per caliper
The innovative stahlbus vent valve allows you to change the brake fluid easily and without help. Clean, totally safe and fast !
This auto bleed valve combines all these advantages:

• Completely sealed by O-ring.
• Hydraulic system remains sealed even during the venting process.
• Reliable non-return function, thus one-man operation.
• System has been bled in minutes.
• Wear of the threads in the caliper is prevented (up and screwing down during the bleeding process).
• For all hydraulic systems such as brakes and clutches stahlbus brake bleed valve just replaces the existing vent screw.
• Tested under extreme conditions by TÃœV Rheinland.
  See BRA41652 for bleed valve cover

   1 in stock

  [ CLOSE WINDOW ]
  [ CLOSE WINDOW ]