Reconditioned Valeo starter motor and solenoid in black and silver finish. Professionally reconditioned and sold with a 12 month guarantee. This is a suitable replacement for Bosch 8 or 9 tooth Guzzi starter motors. Minor modification may be required on some pre 1990 models to make room for the solenoid. Please note that this item may be fitted to Loop frame models with some modifications as described in Guzziology. See , see this link for the modifications required to fit a Valeo starter to a 4 speed model.

This is an exchange only item, we can supply these before receiving your exchange unit subject to a refundable deposit so you can keep your bike on the road. See ELC10737 for the refundable deposit. Send your old starter motor to our registered address. NB In case of starter motor problems do not tap the casing as this will certainly cause it to fail. See SSA08075 for mounting bolts. Also known as Guzzi ref. 30730710
Do not remove second nut from terminal posts when fitting - this nut is required to hold the terminal in place

Supercedes Guzzi refs. 12730705, 14730554 and 14730705

 30730711 GU30730711 30 73 07 11
 3073 0711 3073.0711 30.73.07.11

Complete replica sump for 850, 1000 and some 1100 models. Out of production for years, this is a good opportunity to replace a chipped or cosmetically damaged sump on your Guzzi

 This part is available by special order, request a quote

 14003500 GU14003500 14 00 35 00
 1400 3500 1400.3500 14.00.35.00

Pair of adjustable Tarozzi clipons, quality aluminium castings and chrome plated tube

38mm rise

 Sorry, this part is no longer available.

Splined drive plate incorporating cush drive (rubbers not included)

See WHA14336 for cush drive rubbers

 This part is available by special order, request a quote

 14335203 GU14335203 14 33 52 03
 1433 5203 1433.5203 14.33.52.03

Pair of chrome reverse cone mega type silencers supplied with shims to allow fitment to a variety of models. Adjustable mounting bracket and clamp included.

You may need to modify brackets or fabricate your own depending upon which model you have

 This part is available by special order, request a quote

Alternator stator for Bosch charging systems, this does not include the plate and brush holders

To fit this you will need to solder in the three wires from the windings. Replacement rotors and brushes also available. See ELA00503 for a complete higher output upgrade for your charging system

 This part is available by special order, request a quote

 17712400 GU17712400 17 71 24 00
 1771 2400 1771.2400 17.71.24.00

Black steel centre stand without springs or brackets

Brackets, bushes and springs available separately.
Note that as with the original stand the lugs on this stand are only intended for pushing the stand to the ground and are not stong enough to lever your bike onto the stand. You should put your foot onto the foot of the stand to rock the bike back and up on to it

 Sorry, this part is no longer available.

17430345-z 17430345 GU17430345 17 43 03 45
 1743 0345 1743.0345 17.43.03.45

Replacement clutch plate for single plate RAM clutches

Torque setting for fitting this is 25Nm with a thread locking compound

 This part is available by special order, request a quote

Motoplat ignition unit for one cylinder (2 required per bike)

Also known as Guzzi ref. 23721493, 27721435, 23721491, 23721490, 27721435

 This part is available by special order, request a quote

 23721494 GU23721494 23 72 14 94
 2372 1494 2372.1494 23.72.14.94

Rear main bearing flange

 This part is available by special order, request a quote

12011400-z 12011400 GU12011400 12 01 14 00
 1201 1400 1201.1400 12.01.14.00