Shop headings: New Spares | Used Spares | Accessories | Brands
Short alloy bellmouth / trumpet intake with domed mesh for Dellorto PHF 30 and 36 carbs, screws to rear of carb replacing air filter
2 in stock
£46.00
INC VAT
£38.33 EX VAT
Short alloy bellmouth intake / trumpet with mesh for Dellorto PHM 40 carb, screws to rear of carb replacing air filter
2 in stock
£46.00
INC VAT
£38.33 EX VAT
Rubber sleeved folding riders footpeg, suitable for Tarozzi rearsets and as an upgrade for standard footrests
Folding footrest
2 in stock
£46.00
INC VAT
£38.33 EX VAT
Lightweight 5mm battery plate in a silver finish, supplied with countersunk M8 screws
This is an upgrade to the standard steel plate, perfect for your Tonti framed special (it will also fit Cali 1100 and Cali EV based specials. On some models you may need to enlarge the cut out for the speedo cable
Availability varies on this part, check availability
14418200-z 14418200 GU14418200 14 41 82 00
1441 8200 1441.8200 14.41.82.00
£45.30
INC VAT
£37.75 EX VAT
Plastic inlet manifold, replaces unavailable aluminium manifold. Suitable for PHM 40 carb conversions on models previously fitted with smaller carbs. Contains inlet manifold, gasket, O rings, clip and M6 bolts to secure to head. Carb mounts direct to this manifold (no inlet manifold rubber required)
Note that on models with M8 inlet manifold bolts and standard heads (T3, 1000 SP) it will be necessary to drill out the manifold bolt holes from 6mm to 8mm to reuse your existing bolts
This part is available by special order, request a quote
£45.00
INC VAT
£37.50 EX VAT
Plastic inlet manifold, replaces unavailable aluminium manifold. Contains inlet manifold, gasket, O rings, clip and M6 bolts to secure to head. PHF36 carb mounts direct to this manifold (no inlet manifold rubber required)
Note that on models with M8 inlet manifold bolts and standard heads (T3, 1000 SP) it will be necessary to drill out the manifold bolt holes from 6mm to 8mm to reuse your existing bolts
This part is available by special order, request a quote
£45.00
INC VAT
£37.50 EX VAT
Ignition switch bracket, attaches to top frame tube
See ELA17735 for ignition switch
This part is available by special order, request a quote
17736450 GU17736450 17 73 64 50
1773 6450 1773.6450 17.73.64.50
£45.00
INC VAT
£37.50 EX VAT
Needle roller bearing for crownwheel
1 in stock
92254340 GU92254340 92 25 43 40
9225 4340 9225.4340 92.25.43.40
£44.10
INC VAT
£36.75 EX VAT
Dimensions:
40mm diameter body x 140mm overall (Length may sometimes vary slightly depending upon supplier).
12 volt single lead ignition coil
Suitable for points and Motoplat equipped big twins. NB models with Digiplex ignition use ELA30716. HT lead screws into this HT lead
4 in stock
14716502 GU14716502 14 71 65 02
1471 6502 1471.6502 14.71.65.02
Also fits Ducati, MZ ETZ 250/251
£44.00
INC VAT
£36.67 EX VAT
Stud to mount gearbox onto clutch bellhousing
This part is available by special order, request a quote
£44.00
INC VAT
£36.67 EX VAT