Brembo brake caliper rebuild kit for one P2 F08 (P8) caliper, contains 2 pairs of seals, O ring and 2 M10 bolts

This seal kit is for F08 calipers fitted to front of all these models. Also used on some Triumph Bonnevilles, MZs, Ducati 600 Pantah, 500 Pantah, 500 Sport Desmo, 500 GTV, 650 SL, 750 F1, 750 F1B, 750 Paso, 750 Sport, 900 MHR, 900 SS, 900 S2, 906 Paso, 100 R1, 100 S2 Desmo, Laverda Jota 1000 and Laverda 1200 Anniversary. Brembo ref. 120274110

See BRA10310 for less expensive replica kit

 More than 5 in stock

 14659000 GU14659000 14 65 90 00
 1465 9000 1465.9000 14.65.90.00

Also fits Benelli 354, Benelli Sei, Ducati 250/350/450 Desmo (-1976), Ducati Pantah, Ducati F1, Ducati 750 Paso (1987-1990), Ducati 750 Sport (1988-1990), Ducati 860 GT/GTS, Ducati 900 GTS, Ducati Hailwood Rep, Ducati 900 Darmah (1977-1978), Ducati 906 Paso (1988-1989), Ducati 1000 R1 Hailwood Ref., Hesketh, Horex HRD 600, Horex 500/600 Columbus, Laverda 750 SF2, Laverda 750 SFC, Laverda 750 SF3, Laverda 1000 3C (1974-1978), Laverda 1000 3CL (1976-1981), Laverda 1000 RGS/RGA, Laverda 1000 SFC, Laverda 1200 (1978-1979), Laverda 1200 TS/Mirage (1981), MZ ETZ 125/150/250/300 (1985-1992), Norton Classic (1989), Norton Interpol (1989), Triumph T140 (1985-1988 Brembo)

Dellorto accelerator pump diaphragm for PHF and PHM carbs

Also known as Guzzi ref 075527555

 2 in stock

 14931050 GU14931050 14 93 10 50
 1493 1050 1493.1050 14.93.10.50

Polished adjustable aluminium brake lever for PS 11, PS 13 and PS 16 master cylinders

Also known as Guzzi ref. 10270652. See HAA10850 for lever pivot pin and BRA01630 for span adjustable alternative lever

 1 in stock

30605680-z 30605680 GU30605680 30 60 56 80
 3060 5680 3060.5680 30.60.56.80

Black plastic pillion backrest embossed with 'Moto Guzzi'

Attaches via two 6mm studs

 1 in stock

 03468210 GU03468210 03 46 82 10
 0346 8210 0346.8210 03.46.82.10

10 spline connection sleeve to connect drive box to driveshaft

 This part is due back in stock soon, call 01484 841395 to reserve yours

12327700-z 12327700 GU12327700 12 32 77 00
 1232 7700 1232.7700 12.32.77.00

Full seal kit and gasket set for overhauling the rear drive box

Bearings available separately

 More than 5 in stock

Manually operated fuel tap or fuel valve. Operated by turning base of tap. Supplied with nut and sealing washer

Can be used to replace electronic fuel solenoid valve 03105300 and manual fuel tap 29105460

 More than 5 in stock

 01105460 GU01105460 01 10 54 60
 0110 5460 0110.5460 01.10.54.60

Con rod bearing shell

4 required per engine. Also known as Guzzi ref. 12062000, 12062005, 28062050 Hole pattern may vary from the original part

 4 in stock

 30062000 GU30062000 30 06 20 00
 3006 2000 3006.2000 30.06.20.00

Upper throttle cable for carb models, connects to splitter under tank. One required

We advise you to measure your existing cable before ordering in case you have a non standard set up.

 1 in stock

 30117560 GU30117560 30 11 75 60
 3011 7560 3011.7560 30.11.75.60

Adjustable front black brake lever for PS 11, PS 13 and PS 16 rectangular master cylinder.

Also known as Guzzi ref. 28605678. See BRA01630 or BRA01640 for a span adjustable alternative and HAA10850 for lever pivot pin

 This part is due back in stock soon, call 01484 841395 to reserve yours

10270640-z 10270640 GU10270640 10 27 06 40
 1027 0640 1027.0640 10.27.06.40