The innovative stahlbus bleeder valve allows you to change the brake fluid yourself without assistance.

Linked Guzzi brake systems are notoriously tricky to bleed, this special bleed nipple can save you hours of tedious squeezing and pumping! This banjo bolt can be used in place of a standard fine thread M10 banjo bolt. Supplied with crush washers. We recommend fitting one of these brake valves per caliper
The innovative stahlbus vent valve allows you to change the brake fluid easily and without help. Clean, totally safe and fast !
This auto bleed valve combines all these advantages:

• Completely sealed by O-ring.
• Hydraulic system remains sealed even during the venting process.
• Reliable non-return function, thus one-man operation.
• System has been bled in minutes.
• Wear of the threads in the caliper is prevented (up and screwing down during the bleeding process).
• For all hydraulic systems such as brakes and clutches stahlbus brake bleed valve just replaces the existing vent screw.
• Tested under extreme conditions by TÃœV Rheinland.
  See BRA41652 for bleed valve cover

   1 in stock

  [ CLOSE WINDOW ]
  [ CLOSE WINDOW ]

Left hand chome mirror, especially suited to T3, V50 and similar models. Flat lens.

M10 thread

 This part is due back in stock soon, call 01484 841395 to reserve yours

Right hand chome mirror, especially suited to T3, V50 and similar models. Flat lens.

M10 thread

 This part is due back in stock soon, call 01484 841395 to reserve yours

Chrome bar end mirror with a large round head and adjustable arm. Fits all models with open ended (i.e. not threaded) 7/8 inch steel handlebars.

Can be fitted on either left or right hand side of handlebars. Shown here fitted to a handlebar which is not included

 1 in stock

Small round left hand bar end mirror finished in black. Knuckle allows adjustment of mirror. Fits all models with open ended (i.e. not threaded) 7/8 inch steel handlebars.

Perfect for achieving that minimal look on your bike

 Availability varies on this part, check availability

Kit containing 6 titanium shouldered retaining screw for rocker cover. Upgrade your corrosion prone zinc OE parts with a polished upgrade. Note that one bolt on each cover is hidden under a plastic cover, if you would prefer to only buy four bolts then see SSA84291

Rocker cover bolt. We recommend that you check length of bolts on your engine before ordering as two lengths of bolt were used. Supercedes Guzzi ref. 976591
See ENA83249 for rubber sealing washer

 More than 5 in stock

 842291 MG842291

Universal hydraulic brake light switch. This hydraulic switch replaces discontinued brakelight switches by bolting in place of a single banjo bolt on the handlebar or rear brake master cylinder

NB stop light switch may be supplied with or without 2 pin block connector. Can be used in place of Guzzi ref. 32657060

 1 in stock

Kit containing two replacement 60cm silicon HT leads, lead ends and 90° plug caps. The leads are suppied as a single double length lead so you can cut it into two leads of the exact required length. Includes crimp on lead ends for standard big twin 12v round coils

Suitable for most models with coils under the tank where the HT lead is not moulded into the ignition coil. We recommend checking what type of plug cap you have and measuring your existing cable run to check this part will fit

 This part is due back in stock soon, call 01484 841395 to reserve yours

"The Carburettor Manual" is a comprehensive guide from Dellorto to the setting up and use of tapered needle motorcycle carburettors. Covers principle of operation of all Dellorto tapered needle carburettors 1970 onwards. 33 pages with colour pictures and diagrams. Also included is the original Dellorto "Tuning Guide 1.1" for carburettors, which gives advice on the choice, setting and use of a Dellorto tapered needle carburettor which includes colour carburettor cross sections showing the multiple stages of carburettor operation. Also contains float height and tapered needle selection tables.

 3 in stock

Lightweight M20 gearbox and drive box filler plug (big twins), drive box level plug (small twins). An aluminium filler plug made in Italy.

 1 in stock

 12022600 GU12022600 12 02 26 00
 1202 2600 1202.2600 12.02.26.00