Polished aluminium instrument console kit for 80mm instruments (as used on Le Mans 1, 2, T3, V50 etc...). This high quality kit is specially made for Gutsibits and consists of the following parts:

• Polished aluminium clock surround front with 80mm holes for instruments, slotted ignition switch hole and 8mm instrument light holes
• 6 LEDs with chrome bezels (small spade connectors to rear) for indicators, oil, charge system, neutral and high beam warning light
• Polished aluminium instrument surrounds (odometer surround includes hole for reset knob)
• Polished aluminium instrument backs (attach with existing nuts)

Manufactured from 6mm aluminium, this this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives. These kits are often prepared to order so please allow for a couple of days delay before your order is sent.

NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated. Check the depth of your instruments before ordering, this kit is intended for 48mm deep instruments with 60mm stud centres

Instruments with 60 degree or similar angle drives to the rear will require you to enlarge cable cutouts in the plates that make up the rear of the kit

 1 in stock

Extreme performance hybrid maintenance free Motobatt 12 volt battery. MFLEX technology means you have adjustable terminal options and maximum flexibility when installing.

We have sourced this battery especially for high compression big twins which need enhanced cranking amps for starting. Suitable for special builds with non standard battery locations (e.g. under the gearbox). This hybrid battery offers 330 cranking amps for reliable and hassle free starting. This is at least 100% more cranking amps than comparable lead acid or AGM batteries Superior conductivity from pure copper terminals.

Compared to traditional lead acid batteries a hybrid battery is

• 90% STRONGER in cranking power .
• 30% LIGHTER in weight.
• 500% LONGER, in life cycle.
• 50% LOWER in self-discharge rate
• FASTER in charging time.
• CONSTANT CRANKING, in cold weather.
• PROTECTION, against over-charging over-discharging and heat

• COMPATIBLE, with all OEM charging system.
• 200% MORE AH, in Capacity.
• TEMPERATURE STABLE, in all weather conditions.
• LONGER LIFE CYCLE.
• STRONGER CRANKING, in cold weather.
• ADAPTABLE, to lead acid charger.
• MORE CONNECTIONS, extra electronics connections

 Order now and we will post your order within 7 days.

 638733 MG638733

Tubular luggage rack finished in chrome.

 1 in stock

Tubular luggage rack finished in black.

 This part is available by special order, request a quote

Pair of stylish Kappa soft panniers, perfect for V7 and V9 models.

• 550D Polyester construction with PVC coating
• 2mm thick synthetic leather (PU) detailing
• 190D Nylon inner lining material
• 14 litre capacity for each bag
• Product complies with Reach regulations
• Roll-top closure system
• Saddlebag straps with hook and loop fastening closure
• Front handle
• Waterproof removable inner lining with thermo-sealed seams
• Strap with ring loop to fasten to double D-ring
• Front waterproof zip
• KAPPA RAMBLER logo printed on patch
• Bags come with a TNT bag with the KAPPA RAMBLER logo for storage

 Order now and we will post your order within 7 days.

HIgh performance aluminium velocity stack for airbox to throttle body union. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM

This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA10434

Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.

 This part is available by special order, request a quote

This adjustable fuelling modifier uses the lambda sensor signal to the ECU. By modifying that signal it achieves an improvement in low and midrange throttle response. Comes with wiring harness and instruction manual, installation is simple and does not require any specialist tools. Suitable for all single throttle body V7, V9 and V85 TT models.

Rapid Bike EASY: A base level simple plug and play modulator equipped with a microprocessor managing the lambda sensor signal to optimize the air/fuel ratio, improve the engine efficiency and eliminate power gaps typical of the low and medium rpm range.

See installation instructions here.

 This part is available by special order, request a quote

Clutch friction plate

 This part is available by special order, request a quote

2A000969

Pair of sturdy black ABS handguards with fitting hardware, these protect clutch and brake levers from damage as well as providing some weather protection for your hands. Supplied as a pair, a great accessory for UK riding conditions

Single point mounting for easy installation, bar end weights are retained.

 This part is available by special order, request a quote

Clamp on retro style bar end mirror CNC manufactured in aluminium and finished in black, these are a high quality and stylish addition to your Guzzi and much better value than the genuine Guzzi mirrors. Classic oval shape can be flipped for fitting on either side and above or below the handlebars.

The Reverse Retro mirror is made from billet aluminum. Compact, classy and unmistakable design. Simple lines make it a sought-after Classic suitable for a range of styles. The adjustment system and anti-dazzle glass guarantee optimal versatility and comfort.

Requires 13mm on the handlebar to accommodate the mounting, with optional bar end pieces HAA00113 available to extend bars if required. You may need to redrill the locating holes in your handlebars if moving your switchgear 13mm inboard if HAA00113 is not fitted

Perfect for that classic cafe racer look

 This part is available by special order, request a quote