Shop headings: New Spares | Used Spares | Accessories | Brands
Hepco and Becker pannier frames for hard luggage supplied in black. Supplied with fitting hardware and instructions
See LUA61033 for matching panniers
This part is available by special order, request a quote
£295.00
INC VAT
£245.83 EX VAT
Hepco and Becker pannier frames for hard luggage supplied in black. Supplied with fitting hardware and instructions
See LUA61033 for matching panniers
This part is available by special order, request a quote
£315.00
INC VAT
£262.50 EX VAT
K&N high performance air filter, flat paper cartridge type for single throttle body models
This part is due back in stock soon, call 01484 841395 to reserve yours
AP8104924
£70.00
INC VAT
£58.33 EX VAT
HIgh performance aluminium velocity stack for airbox to throttle body union. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM
This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA10434
Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.
This part is available by special order, request a quote
£150.00
INC VAT
£125.00 EX VAT
Piston ring compressing tool, compresses piston rings to fit into bore. Without this tool you risk snapping piston rings, the tool also speeds up the fitting of new rings
For 57mm - 125mm bores, supplied with hex key for bore adjustment. Not suitable for CARC models
This part is available by special order, request a quote
£48.00
INC VAT
£40.00 EX VAT
Rubber grommet for clutch bell housing / flywheel timing hole
Timing hole plug or timing hole bung. Also used to fill holes used to mount Griso factory luggage rack
This part is due back in stock soon, call 01484 841395 to reserve yours
93180220-z 93180220 GU93180220 93 18 02 20
9318 0220 9318.0220 93.18.02.20
£1.60
INC VAT
£1.33 EX VAT
This adjustable fuelling modifier uses the lambda sensor signal to the ECU. By modifying that signal it achieves an improvement in low and midrange throttle response. Comes with wiring harness and instruction manual, installation is simple and does not require any specialist tools. Suitable for all single throttle body V7, V9 and V85 TT models.
Rapid Bike EASY: A base level simple plug and play modulator equipped with a microprocessor managing the lambda sensor signal to optimize the air/fuel ratio, improve the engine efficiency and eliminate power gaps typical of the low and medium rpm range.
See installation instructions here.
This part is available by special order, request a quote
£149.00
INC VAT
£124.17 EX VAT
Rebuild kit for Hengtong rear caliper. This is a comprehensive overhaul kit containing dust seals, fluid seals, o ring, bleed nipple, and dust cap
Caliper seal kit for Hengtong caliper with 22mm pistons
1 in stock
£28.00
INC VAT
£23.33 EX VAT
Pair of fully adjustable Hagon Nitro rear shock absorbers with ten position adjustable damping, and fully progressive preload adjustment. Black anodised body and springs with automatic compression and rebound balance.
Includes C spanner for preload adjustment.
The suspension on the V7 and V9 models is notoriously cheap, these shocks are an excellent suspension upgrade which will transform your bike. Fully adjustable damping and preload allows you to get your bike handling as it should.
Combine with fork upgrade kit SUA35010 to transform the handling of your ride.
All Hagon shocks have a 2 year unlimited kilometer guarantee and are TUV approved. NB these shock absorbers are fitted upside down (Hagon text to top). Also available by special order with chromed springs and/or polished alloy body, please enquire for details
This part is available by special order, request a quote
£525.00
INC VAT
£437.50 EX VAT