Shop headings: New Spares | Used Spares | Accessories | Brands
The innovative stahlbus bleeder valve allows you to change the brake fluid yourself without assistance.
Linked Guzzi brake systems are notoriously tricky to bleed, this special bleed nipple can save you hours of tedious squeezing and pumping! This banjo bolt can be used in place of a standard fine thread M10 banjo bolt. Supplied with crush washers. We recommend fitting one of these brake valves per caliper
The innovative stahlbus vent valve allows you to change the brake fluid easily and without help. Clean, totally safe and fast !
This auto bleed valve combines all these advantages:
This part is due back in stock soon, call 01484 841395 to reserve yours
£33.00
INC VAT
£27.50 EX VAT
Rebuild kit for Brembo Radial Calipers with 34mm pistons fitted to the front of these models. Contains seals, brake grease, washers, bleed screw and dust cap. One kit required per caliper.
Caliper seal kit
This part is available by special order, request a quote
£33.00
INC VAT
£27.50 EX VAT
Left hand chome mirror, especially suited to T3, V50 and similar models. Flat lens.
M10 thread
This part is due back in stock soon, call 01484 841395 to reserve yours
£32.00
INC VAT
£26.67 EX VAT
Right hand chome mirror, especially suited to T3, V50 and similar models. Flat lens.
M10 thread
This part is due back in stock soon, call 01484 841395 to reserve yours
£32.00
INC VAT
£26.67 EX VAT
Chrome bar end mirror with a large round head and adjustable arm. Fits all models with open ended (i.e. not threaded) 7/8 inch steel handlebars.
Can be fitted on either left or right hand side of handlebars. Shown here fitted to a handlebar which is not included
1 in stock
£30.90
INC VAT
£25.75 EX VAT
Small round left hand bar end mirror finished in black. Knuckle allows adjustment of mirror. Fits all models with open ended (i.e. not threaded) 7/8 inch steel handlebars.
Perfect for achieving that minimal look on your bike
Availability varies on this part, check availability
£30.90
INC VAT
£25.75 EX VAT
Universal hydraulic brake light switch. This hydraulic switch replaces discontinued brakelight switches by bolting in place of a single banjo bolt on the handlebar or rear brake master cylinder
NB stop light switch may be supplied with or without 2 pin block connector. Can be used in place of Guzzi ref. 32657060
1 in stock
£29.50
INC VAT
£24.58 EX VAT
Con rod bolt- please check the engine number of your machine to ensure this is the correct bolt
For Breva motors after engine number KP15262, Griso engines after KS14048, Norge engines after 11775, California engines after KT11862, 1200 Sport engines after 11874
This part is available by special order, request a quote
849131 MG849131
£29.00
INC VAT
£24.17 EX VAT
Kit containing two replacement 60cm silicon HT leads, lead ends and 90° plug caps. The leads are suppied as a single double length lead so you can cut it into two leads of the exact required length. Includes crimp on lead ends for standard big twin 12v round coils
Suitable for most models with coils under the tank where the HT lead is not moulded into the ignition coil. We recommend checking what type of plug cap you have and measuring your existing cable run to check this part will fit
This part is due back in stock soon, call 01484 841395 to reserve yours
£28.00
INC VAT
£23.33 EX VAT
"The Carburettor Manual" is a comprehensive guide from Dellorto to the setting up and use of tapered needle motorcycle carburettors. Covers principle of operation of all Dellorto tapered needle carburettors 1970 onwards. 33 pages with colour pictures and diagrams. Also included is the original Dellorto "Tuning Guide 1.1" for carburettors, which gives advice on the choice, setting and use of a Dellorto tapered needle carburettor which includes colour carburettor cross sections showing the multiple stages of carburettor operation. Also contains float height and tapered needle selection tables.
3 in stock
£22.00
(VAT exempt)
£22.00 EX VAT