Shop headings: New Spares | Used Spares | Accessories | Brands
Clevis pin used in brake and gear change linkages, wears over time so well worth replacing on high mileage bikes
Replaces Guzzi refs. 95780265, 95780267, 95770265-Z, 95780265-Z. See BRA95227 for retaining split pin
1 in stock
95770265 GU95770265 95 77 02 65
9577 0265 9577.0265 95.77.02.65
£11.76
INC VAT
£9.80 EX VAT
Dimensions:
For 35mm stanchions, 223mm usable handlebar, 75mm total height, 30mm tall stanchion clamp
Pair of adjustable Tommaselli clipons, quality aluminium castings and chrome plated tube
These clip ons pivot on the central bolt to adjust the handlebar angle, pull back angle is adjusted on the fork stanchion clamp. These clip ons are unsuitable for use with the PS12 handlebar master cylinder. Bar ends are held in by a rivet and some modification will be needed if you wish to fit bar end mirrors.
This part is available by special order, request a quote
£240.00
INC VAT
£200.00 EX VAT
Polished aluminium instrument console kit for 80mm instruments (as used on Le Mans 1, 2, T3, V50 etc...). This high quality kit is specially made for Gutsibits and consists of the following parts:
Manufactured from 6mm aluminium, this this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives. These kits are often prepared to order so please allow for a couple of days delay before your order is sent.
NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated. Check the depth of your instruments before ordering, this kit is intended for 48mm deep instruments with 60mm stud centres
Instruments with 60 degree or similar angle drives to the rear will require you to enlarge cable cutouts in the plates that make up the rear of the kit
1 in stock
£205.00
INC VAT
£170.83 EX VAT
Clutch cable
5 in stock
14093002 GU14093002 14 09 30 02
1409 3002 1409.3002 14.09.30.02
£20.00
INC VAT
£16.67 EX VAT
Clutch cable with adjuster for gearbox end
Note this cable only has a barrel nipple at the gearbox end of the cable
This part is due back in stock soon, call 01484 841395 to reserve yours
17093002 GU17093002 17 09 30 02
1709 3002 1709.3002 17.09.30.02
£17.10
INC VAT
£14.25 EX VAT
Tool for clutch centre gear nut
Half inch socket drive. This is a cheaper aftermarket tool- see TOA14903 for original factory item
1 in stock
14912603 GU14912603 14 91 26 03
1491 2603 1491.2603 14.91.26.03
£39.00
INC VAT
£32.50 EX VAT
Factory tool for clutch centre gear nut, this is a superior design tool intended for repeated use
Designed to fit the original factory spec nut- this may not fit some aftermarket items. See TOA14651 for cheaper aftermarket tool
This part is available by special order, request a quote
14912603 GU14912603 14 91 26 03
1491 2603 1491.2603 14.91.26.03
£70.00
INC VAT
£58.33 EX VAT
Original type clutch friction plate for big twins
2 plates required per clutch overhaul- thicker side of each plate should face transmission. Also check your intermediate plate 12082300. This has shallower splines than the Spada 3 on plates. These are the best fit if you still have the original shallow spline clutch hub. Also known as Guzzi ref. 12084400
Availability varies on this part, check availability
28084460-z 28084460 GU28084460 28 08 44 60
2808 4460 2808.4460 28.08.44.60
£52.00
INC VAT
£43.33 EX VAT
Shallow splined Newfren clutch friction plate for big twins with old shallow splined clutch centre
2 plates required per clutch overhaul- thicker side of each plate should face transmission. Also check your intermediate plate 12082300. This has shallower splines than the Spada 3 on plates. These are the best fit if you still have the original shallow spline clutch hub
This part is available by special order, request a quote
28084460-z 28084460 GU28084460 28 08 44 60
2808 4460 2808.4460 28.08.44.60
£58.00
INC VAT
£48.33 EX VAT
Nut for clutch centre gear CLA30810, fits on gearbox input shaft
See TOA14903 for special tool
3 in stock
93601022-z 93601022 GU93601022 93 60 10 22
9360 1022 9360.1022 93.60.10.22
£10.00
INC VAT
£8.33 EX VAT