Shop headings: New Spares | Used Spares | Accessories | Brands
Taper roller bearing, used for front wheel on loop frame models with 2 shoe front drum
2 required for front wheel on loop frame models. Also known as Guzzi ref. 92201421. Rear wheel bearing for loop frames (2 required) and V7 Sport / 750S
See WHA90249 for bearing seal
This part is due back in stock soon, call 01484 841395 to reserve yours
92246922-z 92246922 GU92246922 92 24 69 22
9224 6922 9224.6922 92.24.69.22
£29.80
INC VAT
£24.83 EX VAT
Universal hydraulic brake light switch. This hydraulic switch replaces discontinued brakelight switches by bolting in place of a single banjo bolt on the handlebar or rear brake master cylinder
NB stop light switch may be supplied with or without 2 pin block connector. Can be used in place of Guzzi ref. 32657060
2 in stock
£29.50
INC VAT
£24.58 EX VAT
Threaded exhaust flange and nut set, two required per engine
This part is due back in stock soon, call 01484 841395 to reserve yours
12120200 GU12120200 12 12 02 00
1212 0200 1212.0200 12.12.02.00
£29.00
INC VAT
£24.17 EX VAT
36mm exhaust valve
This part is available by special order, request a quote
12036100 GU12036100 12 03 61 00
1203 6100 1203.6100 12.03.61.00
£28.80
INC VAT
£24.00 EX VAT
10 spline connection sleeve to connect drive box to driveshaft
This part is due back in stock soon, call 01484 841395 to reserve yours
12327700-z 12327700 GU12327700 12 32 77 00
1232 7700 1232.7700 12.32.77.00
£28.20
INC VAT
£23.50 EX VAT
Con rod bearing shell
4 required per engine. Also known as Guzzi ref. 12062000, 12062005, 28062050 Hole pattern may vary from the original part
4 in stock
30062000 GU30062000 30 06 20 00
3006 2000 3006.2000 30.06.20.00
£28.00
INC VAT
£23.33 EX VAT
Steel intermediate clutch plate
2 in stock
12082300-z 12082300 GU12082300 12 08 23 00
1208 2300 1208.2300 12.08.23.00
£28.00
INC VAT
£23.33 EX VAT
Kit containing two replacement 60cm silicon HT leads, lead ends and 90° plug caps. The leads are suppied as a single double length lead so you can cut it into two leads of the exact required length. Includes crimp on lead ends for standard big twin 12v round coils
Suitable for most models with coils under the tank where the HT lead is not moulded into the ignition coil. We recommend checking what type of plug cap you have and measuring your existing cable run to check this part will fit
This part is due back in stock soon, call 01484 841395 to reserve yours
£28.00
INC VAT
£23.33 EX VAT
Con rod bearing shell 1st oversize -0.254MM
This part is available by special order, request a quote
30062001 GU30062001 30 06 20 01
3006 2001 3006.2001 30.06.20.01
£28.00
INC VAT
£23.33 EX VAT
Con rod bolt
This part is available by special order, request a quote
12062200 GU12062200 12 06 22 00
1206 2200 1206.2200 12.06.22.00
£27.80
INC VAT
£23.17 EX VAT