Polished aluminium instrument console kit for 80mm instruments (as used on Le Mans 1, 2, T3, V50 etc...). This high quality kit is specially made for Gutsibits and consists of the following parts:

• Polished aluminium clock surround front with 80mm holes for instruments, slotted ignition switch hole and 8mm instrument light holes
• 6 LEDs with chrome bezels (small spade connectors to rear) for indicators, oil, charge system, neutral and high beam warning light
• Polished aluminium instrument surrounds (odometer surround includes hole for reset knob)
• Polished aluminium instrument backs (attach with existing nuts)

Manufactured from 6mm aluminium, this this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives. These kits are often prepared to order so please allow for a couple of days delay before your order is sent.

NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated. Check the depth of your instruments before ordering, this kit is intended for 48mm deep instruments with 60mm stud centres

Instruments with 60 degree or similar angle drives to the rear will require you to enlarge cable cutouts in the plates that make up the rear of the kit

 1 in stock

Clutch cable with adjuster for gearbox end

 1 in stock

 13093048 GU13093048 13 09 30 48
 1309 3048 1309.3048 13.09.30.48

Clutch cable with adjuster for gearbox end

 1 in stock

 12093045 GU12093045 12 09 30 45
 1209 3045 1209.3045 12.09.30.45

Clutch cable with adjuster for gearbox end.

 This part is due back in stock soon, call 01484 841395 to reserve yours

 13093063 GU13093063 13 09 30 63
 1309 3063 1309.3063 13.09.30.63

Splined clutch gear for 4 speed loop frame models

 This part is available by special order, request a quote

12081801-z 12081801 GU12081801 12 08 18 01
 1208 1801 1208.1801 12.08.18.01

Tool for clutch centre gear nut

Half inch socket drive. This is a cheaper aftermarket tool- see TOA14903 for original factory item

 1 in stock

 14912603 GU14912603 14 91 26 03
 1491 2603 1491.2603 14.91.26.03

Factory tool for clutch centre gear nut, this is a superior design tool intended for repeated use

Designed to fit the original factory spec nut- this may not fit some aftermarket items. See TOA14651 for cheaper aftermarket tool

 This part is available by special order, request a quote

 14912603 GU14912603 14 91 26 03
 1491 2603 1491.2603 14.91.26.03

Original type clutch friction plate for big twins

2 plates required per clutch overhaul- thicker side of each plate should face transmission. Also check your intermediate plate 12082300. This has shallower splines than the Spada 3 on plates. These are the best fit if you still have the original shallow spline clutch hub. Also known as Guzzi ref. 12084400

 Availability varies on this part, check availability

28084460-z 28084460 GU28084460 28 08 44 60
 2808 4460 2808.4460 28.08.44.60

Shallow splined Newfren clutch friction plate for big twins with old shallow splined clutch centre

2 plates required per clutch overhaul- thicker side of each plate should face transmission. Also check your intermediate plate 12082300. This has shallower splines than the Spada 3 on plates. These are the best fit if you still have the original shallow spline clutch hub

 This part is available by special order, request a quote

28084460-z 28084460 GU28084460 28 08 44 60
 2808 4460 2808.4460 28.08.44.60

Nut for clutch centre gear CLA30810, fits on gearbox input shaft

See TOA14903 for special tool

 3 in stock

93601022-z 93601022 GU93601022 93 60 10 22
 9360 1022 9360.1022 93.60.10.22