Shop headings: New Spares | Used Spares | Accessories | Brands
Rear brakeline from splitter or proportioning valve to rear caliper fixed pipe. Also used as lower front right hand pipe to caliper fixed pipe on T3
Original type rubber brakeline with chunky galvanized ends
This part is due back in stock soon, call 01484 841395 to reserve yours
17657550
£40.00
INC VAT
£33.33 EX VAT
Lightweight folding Tarozzi aluminium pillion footrest on zinc finish steel bracket footpeg. Footpeg is hollow with rubber Sleeve. Supplied with nyloc nut and washer.
A great way to tidy up the pillion footrests on your project bike
2 in stock
01163620 GU01163620 01 16 36 20
0116 3620 0116.3620 01.16.36.20
£39.90
INC VAT
£33.25 EX VAT
Steel fixed rear brake pipe with threaded connectors at each end
Rigid brake pipe
This part is available by special order, request a quote
17658650 GU17658650 17 65 86 50
1765 8650 1765.8650 17.65.86.50
£39.90
INC VAT
£33.25 EX VAT
Replacement pannier to frame lock for all Hepco and Becker panniers. This is the lock at the rear of the panniers that secures it to the pannier frame plate
Supplied with key, barrel, lock plate, rivets and fitting instructions. Includes pannier frame plate LUA70114
1 in stock
£39.60
INC VAT
£33.00 EX VAT
Plastic inlet manifold, replaces unavailable aluminium manifold. Suitable for PHF 30 carb conversions on models previously fitted with VHB30 carbs. Contains inlet manifold, gasket, O rings, clip and M6 bolts to secure to head. Carb mounts direct to this manifold (no inlet manifold rubber required)
Note that on models with M8 inlet manifold bolts and standard heads (T3, 1000 SP) it will be necessary to drill out the manifold bolt holes from 6mm to 8mm to reuse your existing bolts. Can be used to replace PHF30 inlet manifolds 17116265 and 17116365 which are no longer available. These manifolds exit the heads at a different angle to VHB manifolds and in some cases you may need to modify side panels to allow clearance for air filters
2 in stock
£39.00
INC VAT
£32.50 EX VAT
Piston ring set for Nikasil 83mm bores
These can be used with cast iron bores
1 in stock
14060655-z 14060655 GU14060655 14 06 06 55
1406 0655 1406.0655 14.06.06.55
£39.00
INC VAT
£32.50 EX VAT
Pair of universal chromed handlebars, low rise
Not suitable for V65 GT, Mille GT or other models with wide handlebar clamps. Note wide spacing of knurled sections sits outside handlebar clamps on T3, V50 etc... - see dimensions if in doubt about suitability for your bike
1 in stock
£39.00
INC VAT
£32.50 EX VAT
Tool for clutch centre gear nut
Half inch socket drive. This is a cheaper aftermarket tool- see TOA14903 for original factory item
This part is due back in stock soon, call 01484 841395 to reserve yours
14912603 GU14912603 14 91 26 03
1491 2603 1491.2603 14.91.26.03
£39.00
INC VAT
£32.50 EX VAT
Special Inlet rubber with HT lead guide for late Dellorto PHM carbs with a inlet stub OD of 46mm
Use clip SSA45970
This part will only fit late PHM40 carbs with 46mm inlet stubs, we recommend measuring your carbs before ordering
This part is available by special order, request a quote
£39.00
INC VAT
£32.50 EX VAT
88mm piston ring set for cast and Nigusil bore
3 ring set. Only for Cali 1100 frame prefixes KG and KH, for KC and KD prefixes see ENA30660
4 in stock
18060601-z 18060601 GU18060601 18 06 06 01
1806 0601 1806.0601 18.06.06.01
£38.00
INC VAT
£31.67 EX VAT