One piece rear disc.

Note that this brake disc has 12mm ID mounting holes, you may require bushes if using 8mm bolts. Also known as Guzzi ref. 37635705, 30635731. Always fit new brake pads when replacing a brake disc - BRA27611 or BRA11498

 This part is available by special order, request a quote

 30635701 GU30635701 30 63 57 01
 3063 5701 3063.5701 30.63.57.01

Replacement regulator rectifier for models fitted with the Ducati charging system. This is a quality unit and is supplied with fitting instructions

Connections: 2 x yellow male bullet, 1 x white female bullet, 1 x black ring, 1 x red ring. You will need to reuse your existing block connectors to connect this to your loom. See this wiring diagram for wiring connections

 This part is due back in stock soon, call 01484 841395 to reserve yours

37703805-z 37703805 GU37703805 37 70 38 05
 3770 3805 3770.3805 37.70.38.05

Complete rear brake disc from EBC, 6 hole mounting

Also known as Guzzi ref. 01635700. Always fit new brake pads when replacing a brake disc. Use disc bolt BRA30460

 This part is available by special order, request a quote

306535860

Complete aluminium brake pedal / foot brake lever

High quality reproduction part supplied with bush and rubber. Also known as Guzzi ref. 30677045, 01677010. Can also be fitted to Centauro but the lever is shorter than the original lever.

 This part is available by special order, request a quote

 37677005 GU37677005 37 67 70 05
 3767 7005 3767.7005 37.67.70.05

Rear brake master cylinder PS 11C, foot operated

Can be used as a replacement for the PS12 under tank master cylinder originally fitted to V35 I and V50 II models (which is no longer available). For this conversion note that the PS11 is rod not lever actuated. Also known as Guzzi ref. AP8113502

 This part is available by special order, request a quote

 30666900 GU30666900 30 66 69 00
 3066 6900 3066.6900 30.66.69.00

Deep sump spacer made from alloy. This increases the volume of air in the crankcase and helps reduce 'heavy breathing'. The oil is also better cooled when using one of these. Finished externally in silver paint

To fit this sump spacer you will need longer sump bolts (14 x SSA06055 + 4 x SSA06090) and a pair of sump gaskets (ENA14036). You will also need a longer dipstick, see ENA28005

 Availability varies on this part, check availability

 14003240 GU14003240 14 00 32 40
 1400 3240 1400.3240 14.00.32.40

Brand new budget starter motor and solenoid suitable as a direct replacement for Guzzi Valeo and Bosch 8 or 9 teeth starter motors. You may need to fit hex headed neutral switch bolts on some pre 1990 models to make room for the solenoid. Our part number for the bolt is SSA06016 Please note that this item may be fitted to Loop frame models with some modifications as described in Guzziology, also see https://www.thisoldtractor.com/moto_guzzi_loopframe_starter_-_how_to_replace_the_magneti_marelli_starter_with_a_valeo.html for advice on this upgrade.

Supercedes Guzzi refs. 12730705, 14730554 and 14730705

Get a discount of £20 on this item if you part exchange your existing faulty Valeo or Bosch starter motor.

 1 in stock

 30730711 GU30730711 30 73 07 11
 3073 0711 3073.0711 30.73.07.11

Set of 3 piston rings for Nikasil 92mm bore

Only for Cali 1100 frame prefixes KC and KD, for KG and KH prefixes see ENA18601

 This part is available by special order, request a quote

30060660-z 30060660 GU30060660 30 06 06 60
 3006 0660 3006.0660 30.06.06.60

UK spec Bosch headlamp glass for 180mm headlight, supplied with seal and marked for left hand dip pattern

 This part is available by special order, request a quote

 29740400 GU29740400 29 74 04 00
 2974 0400 2974.0400 29.74.04.00

Superbike top yoke conversion kit which enables the fitment of standard handlebars to improve comfort and ergonomics

To mount the bar clamps you have to drill the necessary 10mm holes into the top yoke. The kit contains a template showing the correct points for drilling. The template has to be fixed by 2 M6-screws on the bottom side of the yoke Use a 10mm drill.

You will also need a set of 22mm handlebars which depending on their height may require longer cables. Available in silver or black- please specify when ordering.

 This part is available by special order, request a quote