Shop headings: New Spares | Used Spares | Accessories | Brands
Genuine Guzzi centrestand, invaluable for maintenance and safe parking
This part is available by special order, request a quote
£205.00
INC VAT
£170.83 EX VAT
Stylish guard to protect your centre stand from damage. This beautifully made part is manufactured from stainless steel plate for maximum protection and longevity. Drilled to save weight this is an essential accessory if you take your Stelvio off road
Sorry, this part is no longer available.
Sorry this item is out of production
Pair of adjustable Tommaselli clipons, quality aluminium castings and chrome plated tube
38mm rise, these clip ons pivot on the central bolt to adjust the handlebar angle, pull back angle is adjusted on the fork stanchion clamp. These clip ons are unsuitable for use with the PS12 handlebar master cylinder fitted to small twins unless the master cylinder is modified. Bar ends are held in by a rivet and some modification will be needed if you wish to fit bar end mirrors.
This part is available by special order, request a quote
£159.00
INC VAT
£132.50 EX VAT
Dimensions:
For 35mm stanchions, 223mm usable handlebar, 75mm total height, 30mm tall stanchion clamp
Pair of adjustable Tommaselli clipons, quality aluminium castings and chrome plated tube
These clip ons pivot on the central bolt to adjust the handlebar angle, pull back angle is adjusted on the fork stanchion clamp. These clip ons are unsuitable for use with the PS12 handlebar master cylinder. Bar ends are held in by a rivet and some modification will be needed if you wish to fit bar end mirrors.
This part is available by special order, request a quote
£240.00
INC VAT
£200.00 EX VAT
Dimensions:
For 38mm stanchions, 223mm usable handlebar, 75mm total height, 30mm tall stanchion clamp
Pair of adjustable Tommaselli clipons, quality aluminium castings and chrome plated tube
These clip ons pivot on the central bolt to adjust the handlebar angle, pull back angle is adjusted on the fork stanchion clamp. These clip ons are unsuitable for use with the PS12 handlebar master cylinder. Bar ends are held in by a rivet and some modification will be needed if you wish to fit bar end mirrors.
This part is available by special order, request a quote
£240.00
INC VAT
£200.00 EX VAT
Dimensions:
6mm thick aluminium, 70mm centres on M8 mounting holes, for 48mm deep instruments with 60mm stud centres
Polished aluminium instrument console kit for 80mm instruments (as used on Le Mans 1, 2, T3 etc...). This high quality kit is specially made for Gutsibits and consists of the following parts:
Manufactured from 6mm aluminium, this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives.
NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated.
Note that on models with an electronic tacho (e.g. Cali 3) the stud hole spacing may be a few mm out and you will needto drill new stud holes in the rear of the surround. You may also need to very slightly enlarge the warning light holes
2 in stock
£205.00
INC VAT
£170.83 EX VAT
Polished aluminium instrument console kit for 80mm instruments (as used on Le Mans 1, 2, T3, V50 etc...). This high quality kit is specially made for Gutsibits and consists of the following parts:
Manufactured from 6mm aluminium, this this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives. These kits are often prepared to order so please allow for a couple of days delay before your order is sent.
NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated. Check the depth of your instruments before ordering, this kit is intended for 48mm deep instruments with 60mm stud centres
Instruments with 60 degree or similar angle drives to the rear will require you to enlarge cable cutouts in the plates that make up the rear of the kit
1 in stock
£205.00
INC VAT
£170.83 EX VAT
Pair of factory engine crash bars finished in black essential for protecting the exposed header pipes and cylinders from expensive damage
You can mount the factory LED spotlight kit ACA02059 to these bars
Fitting kit ACA01999 also required.
1 in stock
2S002028
£151.00
INC VAT
£125.83 EX VAT
Pair of quality Hepco and Becker engine crash bars finished in black essential for protecting the exposed header pipes and cylinders from expensive damage
This part is available by special order, request a quote
£220.00
INC VAT
£183.33 EX VAT
German made chrome lightbar and heavy duty stainless steel spotlights. Single beam spotlights supplied with brackets, bulbs, sheathing, fuses and lead wires. A large central bracket mounts to a existing holes in your lower yoke and positions the lightbar far enough forward to fit this lightbar in conjunction with a screen
Fits all models, with or without screen
This part is available by special order, request a quote
£285.00
INC VAT
£237.50 EX VAT