Shop headings: New Spares | Used Spares | Accessories | Brands
Hepco 'Easy' luggage rack for V100. Designed for Hepco top boxes it features a pillion grab handle which folds flat when not in use (or when a top box is fitted). The rack is easy to fit and transforms your V100 into a capable touring bike.
No additional adapters needed for standard Hepco top boxes with metal locks. If fitting pannier frames you will need to fit either this rack or LUA02097
This part is available by special order, request a quote
£210.00
INC VAT
£175.00 EX VAT
Special rack for mounting a H & B top box to the V85 TT. Complete with hinged case stop, this Alu-Rack allows you to fit Xplorer and Junior top boxes to your bike using the standard quick release top case fitting
This part is available by special order, request a quote
£199.00
INC VAT
£165.83 EX VAT
Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with 12 volt 3 Ohm coils ELA14500 (big twins) and can be used to replace Digiplex on models with Ducati charging systems where the bike is converted to carburettors. This kit is just an ignition system, it will not control fuelling. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.
2 year warranty on Sachse ignition kits
Once fitted no further adjustment should be necessary. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. See this link for fitting instructions. Some bikes may need at least one additional spacer to allow enough clearance for alternator cover to fit once pickup is fitted. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA14500
This part is available by special order, request a quote
£395.00
INC VAT
£329.17 EX VAT
Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with standard 3 Ohm 12 volt coils and can be used to replace points or Motoplat ignition on models with Saprisa charging systems. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.
2 year warranty on Sachse ignition kits
Eliminates vague timing due to worn distributors on big twins. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. Once fitted no further adjustment should be necessary. See this link for fitting instructions. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA31165
This part is available by special order, request a quote
£395.00
INC VAT
£329.17 EX VAT
Stainless steel fasteners kit for PHF and PHM carb models with sump extension.This kit contains nuts, bolts and washers for the following: rocker covers, timing cover, gearbox bell housing, alternator cover, gearbox rear cover, neutral switch, drive box to swingarm, starter motor, head studs, exhaust flanges, inlet manifolds and sump. Just what you need to brighten up your Guzzi and ensure nuts and bolts don't seize on your bike
This engine bolt kit contains appropriate M6, M8, M10 socket cap and hex head bolts, nuts and washers. 149 pieces. To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070). You may also require a replacement front engine bolt kit in stainless (SSA14450) or distributor screws (SSA05025 and SSA04008)
More than 5 in stock
£85.00
INC VAT
£70.83 EX VAT
Stainless steel fasteners kit for VHB carb models with sump extension.This kit contains nuts, bolts and washers for the following: rocker covers, timing cover, gearbox bell housing, alternator cover, gearbox rear cover, neutral switch, drive box to swingarm, starter motor, head studs, exhaust flanges, inlet manifolds and sump. Just what you need to brighten up your Guzzi and ensure nuts and bolts don't seize on your bike
This engine bolt kit contains appropriate M6, M8, M10 socket cap and hex head bolts, nuts and washers. 149 pieces. To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070). You may also require a replacement front engine bolt kit in stainless (SSA14450) or distributor screws (SSA05025 and SSA04008)
More than 5 in stock
£85.00
INC VAT
£70.83 EX VAT
Stainless steel fasteners kit for PHF and PHM carb models without sump extension.This kit contains nuts, bolts and washers for the following: distributor clamp, rocker covers, timing cover, gearbox bell housing, alternator cover, gearbox rear cover, neutral switch, drive box to swingarm, starter motor, head studs, exhaust flanges, inlet manifolds and sump. Just what you need to brighten up your Guzzi and ensure nuts and bolts don't seize on your bike
This engine bolt kit contains appropriate M6, M8, M10 socket cap and hex head bolts, nuts and washers. 149 pieces. To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070). You may also require a replacement front engine bolt kit in stainless (SSA14450) or distributor screws (SSA05025 and SSA04008)
More than 5 in stock
£85.00
INC VAT
£70.83 EX VAT
Stainless steel fasteners kit for VHB carb models without sump extension.This kit contains nuts, bolts and washers for the following: rocker covers, timing cover, gearbox bell housing, alternator cover, gearbox rear cover, neutral switch, drive box to swingarm, starter motor, head studs, exhaust flanges, inlet manifolds and sump. Just what you need to brighten up your Guzzi and ensure nuts and bolts don't seize on your bike
This engine bolt kit contains appropriate M6, M8, M10 socket cap and hex head bolts, nuts and washers. 145 pieces. To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070). You may also require a replacement front engine bolt kit in stainless (SSA14450) or distributor screws (SSA05025 and SSA04008)
More than 5 in stock
£85.00
INC VAT
£70.83 EX VAT
Matte black finish front engine guard to protect the front cover of your V100 from stone cips and corrosive road grime. Fit now before damage occurs
This engine cover is manufactured from AW5083 aluminium for toughness. Fit in conjunction with a EXTRA Fenda Extenda ACA58780 for maximum protection.
1 in stock
£50.00
INC VAT
£41.67 EX VAT
Silver finish front engine guard to protect the front cover of you V100 from stone cips and corrosive road grime. Fit now before damage occurs
This engine cover manufactured is from AW5083 aluminium for toughness. Fit in conjunction with a EXTRA Fenda Extenda ACA58780 for maximum protection.
1 in stock
£50.00
INC VAT
£41.67 EX VAT