Shop headings: New Spares | Used Spares | Accessories | Brands
Performance air filter from Pipercross for mk 1 V7 models. 30% more airflow than a standard filter, supplied pre-oiled and ready for lifetime use on your bike. A great way to improve performance on your modern V7 mk 1
This part is due back in stock soon, call 01484 841395 to reserve yours
AP8104242
£41.90
INC VAT
£34.92 EX VAT
K&N high performance air filter, flat paper cartridge type for single throttle body models
1 in stock
AP8104924
£70.00
INC VAT
£58.33 EX VAT
High performance aluminium velocity stack for airbox to throttle body union on single throttle body models. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM
This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA10434
Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.
This part is due back in stock soon, call 01484 841395 to reserve yours
£140.00
INC VAT
£116.67 EX VAT
Short alloy bellmouth / trumpet intake with domed mesh for Dellorto PHBH 30 carb, replacing air filter. Clamp on type
Supplied with fixing clip, carb shown is for illustration purposes
This part is available by special order, request a quote
£41.00
INC VAT
£34.17 EX VAT
The Power Commander is a fuel injection and ignition timing (on some models) adjustment unit that plugs "inline" with the bikes' stock ECU. The Power Commander uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes, some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the Power Commander's onboard microprocessor. Using this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes' ECU (electronic control unit). Removing the Power Commander returns the bike to its previous stock condition. The Power Commander can be ordered preprogrammed with a your choice of several settings, based on the modifications to your bike. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
This is for V7 models with twin throttle bodies, it is not compatible with single throttle body models
This part is available by special order, request a quote
£455.00
INC VAT
£379.17 EX VAT
This adjustable fuelling modifier uses the lambda sensor signal to the ECU. By modifying that signal it achieves an improvement in low and midrange throttle response. Comes with wiring harness and instruction manual, installation is simple and does not require any specialist tools. Suitable for all single throttle body V7, V9 and V85 TT models.
Rapid Bike EASY: A base level simple plug and play modulator equipped with a microprocessor managing the lambda sensor signal to optimize the air/fuel ratio, improve the engine efficiency and eliminate power gaps typical of the low and medium rpm range.
See installation instructions here.
Order now and we will post your order within 7 days.
£149.00
INC VAT
£124.17 EX VAT
Pair of Nitro Race Piggyback Stainless Steel Shocks. Featuring a stainless steel 38mm damper unit with 90mm piggyback reservoir, fully re-buildable, 18mm piston rod, 10 position damping adjustment with automatic compression / rebound balance. 73mm outside diameter natural stainless steel spring, silver anodised aluminium fittings. Fully progressive spring pre-load adjustment. Supplied as a complete pair with mounting bushes, spring adjusting C spanner and 2.5mm hexagon key. These units are designed to be fitted with the damping adjuster at the bottom but will operate in either orientation.
The suspension on the V7 II models is notoriously cheap and is upgraded by most owners, but all V7 models will benefit from this suspension upgrade which will transform handling. Fully adjustable damping and preload allows you to set up your bike handling as it should.
Combine with our fork upgrade kit to transform the handling of your V7.
All Hagon shocks have a 2 year unlimited kilometer guarantee and are TUV approved. Also available by special order with chromed springs and/or polished alloy body, please enquire for details. All Hagon shocks have a 2 year unlimited kilometer guarantee and are TUV approved.
This part is available by special order, request a quote
£695.00
INC VAT
£579.17 EX VAT
Pair of tubular chrome rocker cover protector bars for two valve engines with carbs of twin throttle bodies. These will protect barrels and rocker covers in the unfortunate event of your bike being dropped
These head protectors bolt to the head at three points using existing rocker cover bolts
1 in stock
£64.00
INC VAT
£53.33 EX VAT
Rocker cover screw kit containing 12 replacement stainless steel socket cap bolts for two valve small twin rocker covers. Only one kit required per engine. Only for twin throttle body V7 models
To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070). This kit is for models without billet rocker cover protectors fitted. This kit contains the correct screws for the Breva 750 and 2004 on V7 models but does not include the two flanged M5 screws SSA81523 that fasten the rocker cover covers to the rocker cover (on models other than the V7 Racer)
More than 5 in stock
£5.00
INC VAT
£4.17 EX VAT
Pair of stylish Kappa soft panniers, perfect for V7 and V9 models.
Order now and we will post your order within 7 days.
£168.00
INC VAT
£140.00 EX VAT