Shop headings: New Spares | Used Spares | Accessories | Brands
Complete sump kit which moves the oil filter out from within the sump to a recess under the sump. This simplifies and speeds up oil changes because the sump no longer needs to be removed. Oil cooling is also improved because oil will cool through the body of the filter. The complete sump kit is a simple fit that will speed up oil changes and reduce the risk of stripping crankcase bolts through repeated sump removal. It is very similar to the arrangement on modern CARC models. Replaces sump extension ENA14002. Finished in silver this is a great upgrade for your Guzzi. Uses oil filter SIA14530
Depending on model you may need a longer dipstick e.g. ENA28495. You can calibrate the sump by adding 3l of oil and marking the position on the dipstick. Note that you need to transfer your oil pressure relief valve and the intake screen from your existing sump into this new one. Note also that the stamped steel covers on some oil pressure relief valves flare wider than others so you may need to make a little clearance in order to get the threads started. Also available at additional cost in black by special order - ENA14006
This part is available by special order, request a quote
£450.00
INC VAT
£375.00 EX VAT
Complete sump kit which moves the oil filter out from within the sump to a recess under the sump. This simpifies and speeds up oil changes because the sump no longer needs to be removed. Oil cooling is also improved because oil will cool through the body of the filter. The complete sump kit is a simple fit that will speed up oil changes and reduce the risk of stripping crankcase bolts through repeated sump removal. It is very similar to the arrangement on modern CARC models. The kit consists of:
Depending on model you may need a longer dipstick e.g. ENA28495. You can calibrate the sump by adding 3l of oil and marking the position on the dipstick. Note that you need to transfer your oil pressure relief valve and the intake screen from your existing sump into this new one. Note also that the stamped steel covers on some oil pressure relief valves flare wider than others so you may need to make a little clearance in order to get the threads started. Also available at additional cost in black to special order
This part is available by special order, request a quote
£459.60
INC VAT
£383.00 EX VAT
Stainless steel fasteners kit for VHB carb models without sump extension.This kit contains nuts, bolts and washers for the following: rocker covers, timing cover, gearbox bell housing, alternator cover, gearbox rear cover, neutral switch, drive box to swingarm, starter motor, head studs, exhaust flanges, inlet manifolds and sump. Just what you need to brighten up your Guzzi and ensure nuts and bolts don't seize on your bike
This engine bolt kit contains appropriate M6, M8, M10 socket cap and hex head bolts, nuts and washers. 145 pieces. To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070). You may also require a replacement front engine bolt kit in stainless (SSA14450) or distributor screws (SSA05025 and SSA04008)
More than 5 in stock
£85.00
INC VAT
£70.83 EX VAT
Stainless steel fasteners kit for VHB carb models with sump extension.This kit contains nuts, bolts and washers for the following: rocker covers, timing cover, gearbox bell housing, alternator cover, gearbox rear cover, neutral switch, drive box to swingarm, starter motor, head studs, exhaust flanges, inlet manifolds and sump. Just what you need to brighten up your Guzzi and ensure nuts and bolts don't seize on your bike
This engine bolt kit contains appropriate M6, M8, M10 socket cap and hex head bolts, nuts and washers. 149 pieces. To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070). You may also require a replacement front engine bolt kit in stainless (SSA14450) or distributor screws (SSA05025 and SSA04008)
More than 5 in stock
£85.00
INC VAT
£70.83 EX VAT
Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with standard 3 Ohm 12 volt coils and can be used to replace points or Motoplat ignition on models with Saprisa charging systems. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.
2 year warranty on Sachse ignition kits
Eliminates vague timing due to worn distributors on big twins. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. Once fitted no further adjustment should be necessary. See this link for fitting instructions. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA31165
This part is available by special order, request a quote
£395.00
INC VAT
£329.17 EX VAT
Polished aluminium distributor cover for models with points or electronic ignition. Alternative for plastic cover ENA14420
See SSA05025 for the screws which secure this dizzie cap
This part is due back in stock soon, call 01484 841395 to reserve yours
14715420-z 14715420 GU14715420 14 71 54 20
1471 5420 1471.5420 14.71.54.20
£55.00
INC VAT
£45.83 EX VAT
Polished aluminium blanking plate kit, use when fitting a crankshaft mounted ignition to replace the distributor
Includes O ring and two countersunk screws. See ENA90313 for replacement O ring
This part is due back in stock soon, call 01484 841395 to reserve yours
£17.00
INC VAT
£14.17 EX VAT
Short screw in polished alloy dipstick with O ring for models without a sump extension. Can be used to replace long dipstick and tube on Le Mans 2 and 1000 SP
Will also fit V7 700, V7 Special and 850 GT if high and low levels are transposed from your old dipstick
This part is due back in stock soon, call 01484 841395 to reserve yours
17004951-z 17004951 GU17004951 17 00 49 51
1700 4951 1700.4951 17.00.49.51
£21.00
INC VAT
£17.50 EX VAT
Long screw in polished alloy dipstick with O ring for models with a sump extension but without fairing lowers
2 in stock
28004950-z 28004950 GU28004950 28 00 49 50
2800 4950 2800.4950 28.00.49.50
£24.30
INC VAT
£20.25 EX VAT
Long screw in polished alloy dipstick with O ring for models with fairing lowers (dipstick protrudes through fairing to make oil level checking much simpler and more accurate)
Use this longer dipstick for models fitted with a sump extension, note that the dipstick extension is 80mm long which is shorter than the original part. Supplied with both O rings
This part is available by special order, request a quote
£59.50
INC VAT
£49.58 EX VAT