Shop headings: New Spares | Used Spares | Accessories | Brands
Set of leads for batter charging. Ring terminals for battery, 2 pin connector for charger to plug into. Often required if you charge more than one bike using your Motobatt Smart Charger
2 in stock
£8.50
INC VAT
£7.08 EX VAT
Prolong battery life with this 9 stage smart battery charger, suitable for 6v, 12v AGM and lead acid batteries.
Weatherproof - suitable for use outside 6V / 12V 1A Auto-sensing charger. Suits all AGM, Lead Acid, Calcium and Gel batteries Charges 6v and 12v batteries Ring terminal and alligator clip harnesses included Spark proof Maintains full charge Simple, connect and wait for green light Overload / Short circuit protection See ACA96001 for a spare set of charging leads (e.g. for a separate bike).
1 in stock
£57.00
INC VAT
£47.50 EX VAT
Black Plastic Number Plate Bracket
This part is available by special order, request a quote
31438765 GU31438765 31 43 87 65
3143 8765 3143.8765 31.43.87.65
£39.60
INC VAT
£33.00 EX VAT
Performance air filter from Pipercross for mk 1 V7 models. 30% more airflow than a standard filter, supplied pre-oiled and ready for lifetime use on your bike. A great way to improve performance on your modern V7 mk 1
1 in stock
AP8104242
£41.90
INC VAT
£34.92 EX VAT
K&N high performance air filter, flat paper cartridge type for single throttle body models
1 in stock
AP8104924
£70.00
INC VAT
£58.33 EX VAT
High performance aluminium velocity stack for airbox to throttle body union on single throttle body models. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM
This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA10434
Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.
This part is due back in stock soon, call 01484 841395 to reserve yours
£140.00
INC VAT
£116.67 EX VAT
The Power Commander is a fuel injection and ignition timing (on some models) adjustment unit that plugs "inline" with the bikes' stock ECU. The Power Commander uses original equipment style connectors so that no splicing or cutting of the harness is required. Most installations take less than 15 minutes, some as little as 5 minutes. Changes are made to the bikes fuel and ignition curves via the Power Commander's onboard microprocessor. Using this technology we are able to offer a large area of adjustment without making any permanent changes to the bikes' ECU (electronic control unit). Removing the Power Commander returns the bike to its previous stock condition. The Power Commander can be ordered preprogrammed with a your choice of several settings, based on the modifications to your bike. The unit also comes complete with software and cable link that allows you to change between different maps or make adjustments to a map file.
This is for V7 models with twin throttle bodies, it is not compatible with single throttle body models
This part is available by special order, request a quote
£455.00
INC VAT
£379.17 EX VAT
This adjustable fuelling modifier uses the lambda sensor signal to the ECU. By modifying that signal it achieves an improvement in low and midrange throttle response. Comes with wiring harness and instruction manual, installation is simple and does not require any specialist tools. Suitable for all single throttle body V7, V9 and V85 TT models.
Rapid Bike EASY: A base level simple plug and play modulator equipped with a microprocessor managing the lambda sensor signal to optimize the air/fuel ratio, improve the engine efficiency and eliminate power gaps typical of the low and medium rpm range.
See installation instructions here.
1 in stock
£149.00
INC VAT
£124.17 EX VAT
Pair of fully adjustable and customised to your requirements Matris rear shock absorbers. These are custom built to suit your weight and riding style so that you get the best suspension and ride available for your Guzzi.
As you would expect these are fully adjustable for preload and damping.
Construction consists of an inner pressurized expansion tank (Nitrogen gas N2) with full floating piston for gas/oil separation and a piston shaft made from high tensile chrome plated alloy steel.
Fully re-buildable and re-valveable. All alloy components are anodised for lengevity.
Supplied with black springs (chrome available on request) with automatic compression and rebound balance.
Includes C spanner for preload adjustment.
The suspension on the V7 and V9 models is notoriously cheap, these shocks are an excellent suspension upgrade which will transform your V9 or V7. Fully adjustable damping and preload allows you to get your bike handling as it should.
Combine with a fork upgrade kit to transform the handling of your ride.
All Matris shocks are customised to your requirements so please call us on 01484 841395 to order and allow four weeks for delivery, they will be worth the wait!
This part is available by special order, request a quote
£955.00
INC VAT
£795.83 EX VAT
Pair of fully adjustable and customised to your requirements Matris rear shock absorbers. These are custom built to suit your weight and riding style so that you get the best suspension and ride available for your Guzzi.
As you would expect these are fully adjustable for preload and damping.
Construction consists of an inner pressurized expansion tank (Nitrogen gas N2) with full floating piston for gas/oil separation and a piston shaft made from high tensile chrome plated alloy steel.
Fully re-buildable and re-valveable. All alloy components are anodised for lengevity.
Supplied with black springs (chrome available on request) with automatic compression and rebound balance.
Includes C spanner for preload adjustment.
The suspension on the V7 models is notoriously cheap, these shocks are an excellent suspension upgrade which will transform your V7. Fully adjustable damping and preload allows you to get your bike handling as it should.
Combine with a fork upgrade kit to transform the handling of your ride.
All Matris shocks are customised to your requirements so please call us on 01484 841395 to order and allow four weeks for delivery, they will be worth the wait!
This part is available by special order, request a quote
£995.00
INC VAT
£829.17 EX VAT