Shop headings: New Spares | Used Spares | Accessories | Brands
Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with 12 volt 3 Ohm coils ELA14500 (big twins) and can be used to replace Digiplex on models with Ducati charging systems where the bike is converted to carburettors. This kit is just an ignition system, it will not control fuelling. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.
2 year warranty on Sachse ignition kits
Once fitted no further adjustment should be necessary. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. See this link for fitting instructions. Some bikes may need at least one additional spacer to allow enough clearance for alternator cover to fit once pickup is fitted. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA14500
This part is available by special order, request a quote
£395.00
INC VAT
£329.17 EX VAT
Polished aluminium distributor cover for models with points or electronic ignition. Alternative for plastic cover ENA14420
See SSA05025 for the screws which secure this dizzie cap
This part is due back in stock soon, call 01484 841395 to reserve yours
14715420-z 14715420 GU14715420 14 71 54 20
1471 5420 1471.5420 14.71.54.20
£55.00
INC VAT
£45.83 EX VAT
Polished aluminium blanking plate kit, use when fitting a crankshaft mounted ignition to replace the distributor
Includes O ring and two countersunk screws. See ENA90313 for replacement O ring
This part is due back in stock soon, call 01484 841395 to reserve yours
£17.00
INC VAT
£14.17 EX VAT
Long screw in polished alloy dipstick with O ring for models with a sump extension but without fairing lowers
2 in stock
28004950-z 28004950 GU28004950 28 00 49 50
2800 4950 2800.4950 28.00.49.50
£24.30
INC VAT
£20.25 EX VAT
Long screw in polished alloy dipstick with O ring for models with fairing lowers (dipstick protrudes through fairing to make oil level checking much simpler and more accurate)
Use this longer dipstick for models fitted with a sump extension, note that the dipstick extension is 80mm long which is shorter than the original part. Supplied with both O rings
This part is available by special order, request a quote
£59.50
INC VAT
£49.58 EX VAT
Polished aluminium instrument console kit for 80mm instruments (as used on Le Mans 1, 2, T3, V50 etc...). This high quality kit is specially made for Gutsibits and consists of the following parts:
Manufactured from 6mm aluminium, this this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives. These kits are often prepared to order so please allow for a couple of days delay before your order is sent.
NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated. Check the depth of your instruments before ordering, this kit is intended for 48mm deep instruments with 60mm stud centres
Instruments with 60 degree or similar angle drives to the rear will require you to enlarge cable cutouts in the plates that make up the rear of the kit
1 in stock
£205.00
INC VAT
£170.83 EX VAT
Dimensions:
6mm thick aluminium, 70mm centres on M8 mounting holes, for 48mm deep instruments with 60mm stud centres
Polished aluminium instrument console kit for 80mm instruments (as used on Le Mans 1, 2, T3 etc...). This high quality kit is specially made for Gutsibits and consists of the following parts:
Manufactured from 6mm aluminium, this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives.
NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated.
Note that on models with an electronic tacho (e.g. Cali 3) the stud hole spacing may be a few mm out and you will needto drill new stud holes in the rear of the surround. You may also need to very slightly enlarge the warning light holes
2 in stock
£205.00
INC VAT
£170.83 EX VAT
Dimensions:
For 35mm stanchions, 223mm usable handlebar, 75mm total height, 30mm tall stanchion clamp
Pair of adjustable Tommaselli clipons, quality aluminium castings and chrome plated tube
These clip ons pivot on the central bolt to adjust the handlebar angle, pull back angle is adjusted on the fork stanchion clamp. These clip ons are unsuitable for use with the PS12 handlebar master cylinder. Bar ends are held in by a rivet and some modification will be needed if you wish to fit bar end mirrors.
This part is available by special order, request a quote
£240.00
INC VAT
£200.00 EX VAT
Dimensions:
For 38mm stanchions, 223mm usable handlebar, 75mm total height, 30mm tall stanchion clamp
Pair of adjustable Tommaselli clipons, quality aluminium castings and chrome plated tube
These clip ons pivot on the central bolt to adjust the handlebar angle, pull back angle is adjusted on the fork stanchion clamp. These clip ons are unsuitable for use with the PS12 handlebar master cylinder. Bar ends are held in by a rivet and some modification will be needed if you wish to fit bar end mirrors.
This part is available by special order, request a quote
£240.00
INC VAT
£200.00 EX VAT
Brembo PS 13 handlebar mounted clutch master cylinder, supplied complete with lever.
This part is available by special order, request a quote
£175.00
INC VAT
£145.83 EX VAT