Shop headings: New Spares | Used Spares | Accessories | Brands
Pair of aluminium spacers and gaskets which allow the fitting of a round barrel rocker cover (loop or T3 type) on a square barrel engine
Rocker cover adapter kit - a simple way to get the classic round barrel appearance without swapping barrels and heads. This kit contains a pair of adapter plates and all neccessary gaskets
3 in stock
£70.00
INC VAT
£58.33 EX VAT
Titanium shouldered retaining screw for rocker cover. 4 required for each big twin cylinder head, 3 per head on small twins. Upgrade your corrosion prone zinc OE parts with a polished upgrade.
Rocker cover bolt. We recommend that you check length of bolts on your engine before ordering as two lengths of bolt were used. Supercedes Guzzi ref. 976591
See ENA83249 for rubber sealing washer on CARC models and ENA06716 for sealing washer on other models
3 in stock
842291 MG842291
£5.50
INC VAT
£4.58 EX VAT
Dimensions:
6mm thick aluminium, 70mm centres on M8 mounting holes, for 48mm deep instruments with 60mm stud centres
Polished aluminium instrument console kit for 80mm instruments (as used on Le Mans 1, 2, T3 etc...). This high quality kit is specially made for Gutsibits and consists of the following parts:
Manufactured from 6mm aluminium, this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives.
NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated.
Note that on models with an electronic tacho (e.g. Cali 3) the stud hole spacing may be a few mm out and you will needto drill new stud holes in the rear of the surround. You may also need to very slightly enlarge the warning light holes
2 in stock
£205.00
INC VAT
£170.83 EX VAT
Replacement brake or gear lever for bikes fitted with Tarozzi rearsets
See ACA30060 for rearset kits
2 in stock
£32.40
INC VAT
£27.00 EX VAT
Lever peg for Tarozzi rearset brake and gear levers. Accepts black rubber ACA11601
M8 threaded mounting
2 in stock
£8.70
INC VAT
£7.25 EX VAT
Rubber for Tarozzi rearset gear or brake lever peg. Embossed with Tarozzi
Tarozzi levers and lever ends also available
2 in stock
£4.40
INC VAT
£3.67 EX VAT
Lightweight folding Tarozzi aluminium pillion footrest on zinc finish steel bracket footpeg. Footpeg is hollow with rubber Sleeve. Supplied with nyloc nut and washer.
A great way to tidy up the pillion footrests on your project bike
2 in stock
01163620 GU01163620 01 16 36 20
0116 3620 0116.3620 01.16.36.20
£39.90
INC VAT
£33.25 EX VAT
Short alloy bellmouth / trumpet intake with domed mesh for Dellorto PHF 30 and 36 carbs, screws to rear of carb replacing air filter
2 in stock
£46.00
INC VAT
£38.33 EX VAT
Long alloy bellmouth / trumpet intake with domed mesh for Dellorto PHF 30 and 36 carbs, screws to rear of carb replacing air filter
2 in stock
£52.00
INC VAT
£43.33 EX VAT
Short alloy bellmouth intake / trumpet with mesh for Dellorto PHM 40 carb, screws to rear of carb replacing air filter
2 in stock
£46.00
INC VAT
£38.33 EX VAT