Front wheel bearing. Two required. See WHA81773 for wheel bearing seal.

Front wheel bearing on Cali 1400, two required for Guzzi ref. AP8110094

 Order now and we will post your order within 7 days.

AP8125777

Dimensions:
47mm OD

Complete 950cc piston and Nikasil coated barrel kit including gudgeon pin, piston rings and circlips. Piston is low compression. This kit with Italian made piston and rings is an an alternative to Gilardoni kits which can often be in short supply.

Components for one cylinder.

 Order now and we will post your order within 28 days.

18060102-z 18060102 GU18060102 18 06 01 02
 1806 0102 1806.0102 18.06.01.02

Dimensions:
88mm bore

Complete high quality gasket kit for round barrel 850 models

This is only a gasket set, it does not include oil seals and O rings. The top end O rings required are 12 x ENA97624 and 2 x ENA90203

 This part is due back in stock soon, call 01484 841395 to reserve yours

If you would like to be emailed once this item is available again then click here

17999050-z 17999050 GU17999050 17 99 90 50
 1799 9050 1799.9050 17.99.90.50

Sump gasket for one piece sump

1200 models manufactured before late 2015 used two sump gaskets ENA01651 and ENA05630

 Order now and we will post your order within 28 days.

B063861

Clutch thrust bearing complete, sits in recess in rear gearbox casing.

This bearing is the higher quality OE bearing used on recent models

 1 in stock

2A000376

Dimensions:
22mm OD

Clutch thrust bearing complete, sits in recess in rear gearbox casing.

Not suitable for early 4 speed gearboxes unless modified as per chapter 9 of Guzziology. Also known as Guzzi ref. 2A000376

 1 in stock

12087001-z 12087001 GU12087001 12 08 70 01
 1208 7001 1208.7001 12.08.70.01

Dimensions:
22mm OD

Complete Brembo F08 (P8) front left hand (when mounted behind fork leg, otherwise use as RH) Brembo brake caliper. Also rear caliper (when mounted above and behind rear wheel spindle). Supplied with bleed nipple, dust cover pins and spring, this is a replacement for the Brembo P8 single and twin bleed caliper. This can also be used as a replacement for the P9 caliper used on the 1000 SP rear

Supplied ready to fit and bleed. Also known as Guzzi ref. 28653301, 28652301. Ducati ref. 079937806

 Availability varies on this part, call us to check availability

If you would like to be emailed once this item is available again then click here

 18652201 GU18652201 18 65 22 01
 1865 2201 1865.2201 18.65.22.01

Also fits Benelli 354, Benelli Sei, Ducati, Hesketh

Dimensions:
108mm mounting centres

Roller tappet kit C for converting your 4 valve per cylinder model to the later rollerised tappets

All 4v/cyl 1200 Sport models use this kit.

For Griso and Stelvio your engine will need inspecting to work out which kit is required, this cannot be deduced from engine or chassis number. Further information about which kit you may need can be found here.
For this kit see Moto Guzzi factory bulletin no.02 from 2014. We recommend that you also get your fuelling map updated following this upgrade for maximum benefit

 Order now and we will post your order within 28 days.

1A002082

Black aluminium bar-end mirror kit.; supplier describes the kit as ECE approved.

 This part is available by special order, request a quote

Performance air filter from Pipercross for mk 1 V7 models. 30% more airflow than a standard filter, supplied pre-oiled and ready for lifetime use on your bike. A great way to improve performance on your modern V7 mk 1

 Sorry, this part is no longer available.

AP8104242

Dimensions:
115mm x 155mm x 25mm