Full service kit containing 1 x UFI oil filter, 1 x UFI air filter, 2 x NGK BP6ES spark plugs, 2 x condensers, 1 x set points, 1 x sump gasket, 2 x rocker cover gaskets and all crush washers to complete a service on your points equipped round barrel model.

Save time and hassle by ordering service oil kit OIA14001 with your service kit

Save £'s by buying everything in a service kit

For models with electronic ignition see SIA14002, if you have a deep sump you'll need an extra sump gasket (ENA14036). Oils and lubricants available separately. The oils you need are 1 x OIA11036 and 1 x OIA08194. See ENA95006 for gauze oil filter tab washer

 3 in stock

Chrome twin pull Tommaselli 2c twist grip. Includes a pair of handlebar grips, for bikes with dual throttle cables from the bars

As originally fitted to pre 1979 T3's. Not suitable for carbs larger than 36mm (the twistgrip inner will require minor modification to operate PHM40s). This twistgrip can be used on almost any model with suitable custom cables. See ACA14450 for spare rubber. Holes for throttle cable elbow may be smaller than the original and need carefully enlarging with a drill or round file.

 1 in stock

 14603450 GU14603450 14 60 34 50
 1460 3450 1460.3450 14.60.34.50

Rear crash bar set, bright chrome finish. Supplied without M10 mounting bolts (6 x SSA10025, 6 x SSA10002 and SSA10004 required)

See FRA17750 for mounting plate

 Sorry, this part is no longer available.

 18458250 GU18458250 18 45 82 50
 1845 8250 1845.8250 18.45.82.50

Fuel filler cap supplied with rubber seal

Does not fit early V7 Sport tanks with 54mm aperture

 Availability varies on this part, check availability

13103960-z 13103960 GU13103960 13 10 39 60
 1310 3960 1310.3960 13.10.39.60

Also fits Ducati 350/500 Twin, Ducati 350/500 Twin GTV, Ducati 350/500 Twin Sport, Ducati 450 Desmo, Ducati 500 Sport Desmo, Ducati 750 GT/Sport, Ducati 750/900 SS, Ducati 860/900 GTS, Ducati 900 Darmah, Laverda, Triumph T140 (Meriden)

Tinted standard size screen with mounting holes and beaded edge

Mount this screen using the following parts: FAA60001A (chrome) or FAA60001G (black) + upper arms FAA60001D
See FAA60001B if you just need the screen mounting screws.
To simplify installation always mount a screen on to the mounting brackets before mounting the brackets on the bike

 This part is due back in stock soon, call 01484 841395 to reserve yours

 18577350 GU18577350 18 57 73 50
 1857 7350 1857.7350 18.57.73.50

Complete rear light or tail lamp including plastic shroud, lens, light fitting and steel mounting bracket

Rare and previously unobtainable new. Can be used to replace tail light on Lario and Le Mans 1000, note that this one does not have side 'wings' but is functional on these models

 This part is due back in stock soon, call 01484 841395 to reserve yours

 19750900 GU19750900 19 75 09 00
 1975 0900 1975.0900 19.75.09.00

Also fits Benelli 900 Sei

Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.

Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear

 1 in stock

 01738030 GU01738030 01 73 80 30
 0173 8030 0173.8030 01.73.80.30

Left hand Domino type switchgear with high and low beam, pass, indicator and horn switches. Same style switch as ELA01738

On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. An indication of wire colours is supplied with this switchgear. Supplied with 9 pin block connector. NB does not have lights off - park - on function, you need this to be on your RH switch (e.g. ELA01729 ) or run lights always on

 This part is available by special order, request a quote

Complete shallow bowl 190mm chrome headlight unit. Includes a pilot / parking light. A shallow bowl makes it especially suitable for mounting on Moto Guzzis underneath the instruments

Homologated for road use.

Supplied complete with H4 bulb, pilot light and four short wires (without connectors). This headlight will fit fairing cowling FAA99575 for Le Mans 1 conversions if trim strip is not fitted to inside edge of fairing. NB mounting holes will need drilling out to 10mm if fitting T3 type indicator stems

 Availability varies on this part, check availability

Chrome finish side stand

 This part is available by special order, request a quote

 30432060 GU30432060 30 43 20 60
 3043 2060 3043.2060 30.43.20.60