The BoosterPlug is an effective and cost efficient way to cure the fuelling problems common to all modern fuel injected Guzzi's.
Plugging directly into the wiring harness using original connectors, with no cutting or splicing required, installation takes less than ten minutes.

The BoosterPlug features a unique technology to provide your bike with a controlled fuel enrichment in all ambient temperature situations. No other Plug and Play device does this. A richer mixture is provided only when needed i.e at low RPMs and when accelerating. On open roads at a constant speed the Boosterplug sits idle to keep fuel consumption low.
Make your bike run as it should have done from the factory!

• Improved and gentler throttle action when opening and closing throttle
• Richer mixture when opening the throttle improves acceleration
• Booster plug removes the uneven low speed running that is typical for modern lean burn engines
• Stronger and more consistent at idle.
• Reduced backfiring with aftermarket exhausts on engine braking
• Improved fuel economy

Exhaust stud kit consisting of 4 x titanium studs, 4 x stainless dome head nuts and 4 x stainless wavy washers

The mild steel exhaust studs fitted to modern Guzzis are notorious for corroding in place. Replace yours now with these corrosion resistant parts to ensure you can remove your exhaust in years to come

 5 in stock

1A003632R

1 litre of Agip SAE 10W fork oil. Eni Fork Oil 10W is a product designed for the motorcycle industry designed and developed for use in forks and shock absorbers, suitable for both road and off-road use. The product is part of the Fork Oil series, which includes products with a different viscosity gradient to be selected in relation to the manufacturer's requirements and/or the damping action desired. It is also possible to obtain intermediate grades by mixing with other Fork Oil grades.

As recommended by Guzzi. One litre will refill both forks on most models, check your manual for exact quantity required. 5W also available, use a combination of 5W and 10W to tune your damping more precisely

Eni Fork Oil 10W is equipped with appropriate rheological features such as low temperature fluidity, high viscosity index and a very low sliding point, which results in smooth and uniform suspension behavior in a wide range of temperatures.

This product is characterized by high anti-wear properties, which ensure high protection and long service life to the lubricating parts.

The corrosion-resistant properties of Eni Fork Oil 10W allow effective protection of surfaces against corrosive phenomena.

Eni Fork Oil 10W has the necessary properties for the correct operation of the lubricated equipment, such as low foaming, low air retention, stability in hot conditions, and compatibility with rubber materials (gaskets).
Please note this part CANNOT be posted outside of the UK mainland area. ENI oils were previously sold under the AGIP name

 More than 5 in stock

GU30530527

1 litre of fully synthetic Eni I-Ride Racing 10W-50. Eni i-Ride racing offroad 10W-50 is an innovative lubricant with top synthetic formula set up and developed to meet the lubrication requirements of technology advanced 4-stroke engines that are fitted in off-road and road motorcycles. The exclusive formulation of the Eni i-Ride racing 10W-50 has characteristics that offer maximum performance even in the presence of particularly high stresses such as engines subjected to 'Off-Road' use.

The highly accurate selection of the raw materials that form Eni i-Ride racing 10W-50 makes it possible to achieve the best lubrication conditions of all the mechanical parts of the engine under any extreme driving conditions.

The formulation of Eni i-Ride racing 10W-50 is designed to offer the perfect operation of oil immersed clutches even under limited engagements and disengagements, as required in an off-road use.

The particular additivation selected for Eni i-Ride racing 10W-50 is capable of ensuring a good engine detergency, in particular it has characteristics that allow efficient control of the formation of deposits areas submitted to high temperature.

Eni i-Ride racing 10W-50 has properties which effectively counteract the occurrence of wear in any condition of use.

Surpasses API SL, JASO MA and MA2. ENI oils were previously sold under the AGIP name. 4.9l of this oil required for V100

 More than 5 in stock

1 litre of Agip SAE 15W fork oil, lighter weight than standard on most Guzzi models. Eni Fork Oil 15W is a product designed for the motorcycle industry designed and developed for use in forks and shock absorbers, suitable for both road and off-road use.

As recommended by Guzzi. One litre will refill both forks on most models, check your manual for exact quantity required. 10W also available, use a combination of 10W and 15W to tune your damping more precisely

Please note this part CANNOT be posted outside of the UK mainland area. It is also possible to obtain intermediate grades by mixing with other Fork Oil grades. ENI oils were previously sold under the AGIP name

 More than 5 in stock

Full service kit containing 1 x UFI oil filter, 1 x UFI air filter, crush washer and filter cover O ring, drain and level plug seals to complete a service on your bike

Save £'s by buying everything in a service kit

Guzzi approved ENI oils and lubricants available separately. The oils you need are 2 x OIA01051 for the engine or save time and money by ordering our service oil kit OIA85001. See SIA85888 for the long life spark plugs

 5 in stock

Kit containing 4 Litres of Millers ZFS 4T SAE20W-50 synthetic engine oil and 1 litre of Extreme Pressure gearbox and drivebox oil. This kit contains all the oil you will need to change your engine, drive box and gearbox oil on models with conventional tappets

Please note this kit CANNOT be posted outside of the UK mainland area

 4 in stock

Kit containing 2 Litres of ENI i-Ride Racing SAE10W-60 synthetic engine oil, 1 litre of Extreme Pressure gearbox oil and 1 litre of final drive oil for mk 1 V7 and Breva 750 models. This kit contains all the oils you will need to change your engine, drive box and gearbox oil

Please note this kit CANNOT be posted outside of the UK mainland area

 This part is due back in stock soon, call 01484 841395 to reserve yours

Kit containing 8 long titanium shouldered retaining screws for your rocker covers. Upgrades the poor quality OE screws with shiny Ti parts

Rocker cover bolt kit for single throttle body models. Upgrade your corrosion prone zinc OE parts with a polished upgrade.

 More than 5 in stock

 887483 MG887483