Left hand Domino type switchgear with high and low beam, pass, indicator and horn switches. Same style switch as ELA01738

On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. An indication of wire colours is supplied with this switchgear. Supplied with 9 pin block connector. NB does not have lights off - park - on function, you need this to be on your RH switch (e.g. ELA01729 ) or run lights always on

 This part is available by special order, request a quote

Set of ignition points contacts

 Sorry, this part is no longer available.

 10709600 GU10709600 10 70 96 00
 1070 9600 1070.9600 10.70.96.00

CEV type lights (off/pilot/on), main beam and horn switch. Supplied without wires, you will need to solder your wiring into the switchgear using a minimum 60W soldering iron. Switch fixes to handlebars using included screws

Can be fitted to left or right side of bars

 This part is due back in stock soon, call 01484 841395 to reserve yours

12746001-z 12746001 GU12746001 12 74 60 01
 1274 6001 1274.6001 12.74.60.01

HT lead rubber, used where HT lead screws onto plug cap or pushes onto ignition coil

 This part is due back in stock soon, call 01484 841395 to reserve yours

 14717600 GU14717600 14 71 76 00
 1471 7600 1471.7600 14.71.76.00

Kit containing two replacement 60cm silicon HT leads, lead ends and 90° plug caps. The leads are suppied as a single double length lead so you can cut it into two leads of the exact required length. Includes crimp on lead ends for standard big twin 12v round coils

Suitable for most models with coils under the tank where the HT lead is not moulded into the ignition coil. We recommend checking what type of plug cap you have and measuring your existing cable run to check this part will fit

 This part is due back in stock soon, call 01484 841395 to reserve yours

Push button starter switch, chrome finish body, screw contacts to rear

 This part is available by special order, request a quote

26735001-z 26735001 GU26735001 26 73 50 01
 2673 5001 2673.5001 26.73.50.01

12 volt single output 3 Ohm ignition coil (lead to distributor)

Push fit HT lead, see ELA00001 for crimp on HT lead connector. Supplied without coil clamp

 This part is due back in stock soon, call 01484 841395 to reserve yours

 26716504 GU26716504 26 71 65 04
 2671 6504 2671.6504 26.71.65.04

Silca key blank for ignition key, match profile to your existing key

 This part is due back in stock soon, call 01484 841395 to reserve yours

NE5

Silca key blank for ignition key, match profile to your existing key

 This part is due back in stock soon, call 01484 841395 to reserve yours

Motobatt quadflex 30Ah battery. Quadflex technology means you have two positive and two negative threaded terminals allowing maximum flexibility when installing. This powerful battery produces a massive 390 cranking amps, and is rated at 32 ah.

These sealed absorbed glass matt batteries have been used in military and off road applications for many years.
They offer increased lifespan, higher vibration resistance and electrical performance. This battery is also leak, vibration and spill proof if installed correctly.
Supplied fully charged and ready to fit.

NB This battery must not be trickle charged or charged using a traditional manual charger, AGM batteries require a smart charger - we recommend ACA96000
For more information on charging AGM batteries see these FAQ's.

This is a better value replacement for the Odyssey PC925 battery. Replaces Guzzi refs. 14704550, 18704550, 28704550, 28704545, 28704551, 28704552, 14704551, 14704500 and 14704505

One year warranty on all our Motobatt batteries.

Slightly taller than original loop frame battery so you may need to make some modification to retaining bracket

Please note this part CANNOT be posted outside of the UK mainland area

 Order now and we will post your order within 7 days.

03704540-z 03704540 GU03704540 03 70 45 40
 0370 4540 0370.4540 03.70.45.40