Shop headings: New Spares | Used Spares | Accessories | Brands
Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with 12 volt 3 Ohm coils ELA14500 (big twins) and can be used to replace Digiplex on models with Ducati charging systems where the bike is converted to carburettors. This kit is just an ignition system, it will not control fuelling. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.
2 year warranty on Sachse ignition kits
Once fitted no further adjustment should be necessary. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. See this link for fitting instructions. Some bikes may need at least one additional spacer to allow enough clearance for alternator cover to fit once pickup is fitted. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA14500
This part is available by special order, request a quote
£395.00
INC VAT
£329.17 EX VAT
Long screw in polished alloy dipstick with O ring for models with a sump extension but without fairing lowers
2 in stock
28004950-z 28004950 GU28004950 28 00 49 50
2800 4950 2800.4950 28.00.49.50
£24.30
INC VAT
£20.25 EX VAT
Long screw in polished alloy dipstick with O ring. Will not fit later 4v/cylinder models that have unthreaded dipstick
1 in stock
01004900-z 01004900 GU01004900 01 00 49 00
0100 4900 0100.4900 01.00.49.00
£24.30
INC VAT
£20.25 EX VAT
Polished aluminium instrument console kit for 80mm instruments (as used on Le Mans 1, 2, T3, V50 etc...). This high quality kit is specially made for Gutsibits and consists of the following parts:
Manufactured from 6mm aluminium, this this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives. These kits are often prepared to order so please allow for a couple of days delay before your order is sent.
NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated. Check the depth of your instruments before ordering, this kit is intended for 48mm deep instruments with 60mm stud centres
Instruments with 60 degree or similar angle drives to the rear will require you to enlarge cable cutouts in the plates that make up the rear of the kit
1 in stock
£205.00
INC VAT
£170.83 EX VAT
Carbon fibre tank pad with Moto Guzzi emblem
Stylish way to prevent your tank getting scratched, see ACA04001 for a plain black tank protector
This part is due back in stock soon, call 01484 841395 to reserve yours
£34.00
INC VAT
£28.33 EX VAT
Brembo PS 13 handlebar mounted clutch master cylinder, supplied complete with lever.
This part is available by special order, request a quote
£175.00
INC VAT
£145.83 EX VAT
Replacement blue LED in chrome bezel for Gutsibits clock surrounds ACA01001 and ACA01002
These 12v LEDs include a resistor, wires should be soldered to the mini spade connectors on the base of the LED
More than 5 in stock
£3.40
INC VAT
£2.83 EX VAT
Black and red 60mm round Moto Guzzi badge for Hepco and Becker panniers
Guzzi pannier badge.
This part is due back in stock soon, call 01484 841395 to reserve yours
£13.86
INC VAT
£11.55 EX VAT
Lightweight M20 gearbox and drive box filler plug (big twins), drive box level plug (small twins). An aluminium filler plug made in Italy.
1 in stock
12022600 GU12022600 12 02 26 00
1202 2600 1202.2600 12.02.26.00
£26.00
INC VAT
£21.67 EX VAT
Polished aluminium alternator cover
This is the deeper alternator cover which is suitable for models with Ducati and Saprisa charging systems. It is not compatible with sleeve ENA14710.
See SSA06030 for stainless steel mounting bolts (4 required)
This part is due back in stock soon, call 01484 841395 to reserve yours
18001650-z 18001650 GU18001650 18 00 16 50
1800 1650 1800.1650 18.00.16.50